Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of

Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.10P

See similar textbooks

Similar questions

Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0 kN/m3 and = 33. Assuming = 0.7 and K = 1.4Ko, determine the load carrying capacity of the pile with factor of safety of 3.0.
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Solve Problem 12.23 using the method of Broms. Assume that the pile is flexible and free headed. Let the soil unit weight, = 16 kN/m3; the soil friction angle, = 30; and the yield stress of the pile material. FY = 21 MN/m2. 12.23 A 30 m long concrete pile is 305 mm 305 mm in cross section and is fully embedded in a sand dcposit. If nh = 9200 kN/m2, the moment at ground level Mg = 0, the allowable displacement of pile head = 12 mm; Ep = 21 106 kN/m2, and FY(pile) = 21,000 kN/m2, calculate the allowable lateral load, Qg, at the ground level. Use the elastic solution method.
A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load carrying capacity of the pile with a factor of safety of 3.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load.
A concrete pile 458 mm by 458mm square cross section is embedded in a saturated clay. The length of the embedment is 16 m. The undrained cohesion, Cu of clay is 60 kN/m2, and the unit weight of clay is 18 kN/m2. Use a factor of safety of 5 to determine the allowable load the pile can carry
A rectangular pile (0.91 x 0.54 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 5 m., cohesion of 51 kPa, friction factor of 0.82. Second layer has a height of 5 m., cohesion of 71 kPa, and friction factor of 0.84. Compute the allowable load that the pile can carry if the factor of safety is 2.97