Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 29 kg, while the masses of members OC and AC are 78 kg and 64 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 29 kg 5.9 m- 29 kg B 1.0 64 kg 4.9 m 78 kg C 7.7 m

Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal assembly. Each traffic signal has a mass of 29 kg, while the masses of members OC and AC are 78 kg and 64 kg, respectively. Positive answers are to the right, up, and counterclockwise. A 29 kg 5.9 m- 29 kg B 1.0 64 kg 4.9 m 78 kg C 7.7 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.74P: One end of cable AB is fixed, whereas the other end passes over a smooth pulley at B. If the mass of...

See similar textbooks

Similar questions

One end of cable AB is fixed, whereas the other end passes over a smooth pulley at B. If the mass of the cable is 1.2 kg/m and the sag is H = 1.6 m, determine the mass M that is attached to the free end of. the cable.
Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the member, neglecting its weight. Count the unknowns.
The two uniform cylinders, each of weight W, are resting against inclined surfaces. Neglecting friction, draw the free-body diagrams for each cylinder and for the two cylinders together. Count the total number of unknowns and the total number of independent equilibrium equations.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
At the shown position, the ground reaction forces measured using a force platform are 600N in the vertical direction (Fy) and 200N in horizontal direction (Fx). The mass of the limb below the knee is 4kg with the centre of gravity at the point G. Determine the forces and moment applied to the knee joint. Draw correct free body diagram using any part of the body shown below.
An athlete of 60 kg and 1.70 m tall performs the ring exercise called "the Christ", in which he keeps his body immobile with his arms extended horizontally as shown in Fig.-Prob.17(a). The angle with the vertical of the cords from which the rings hang is theta = 10. (a) Determine the tension T in the cords holding the rings. (b) Considering each arm of the athlete as a rigid horizontal bar subjected to the forces indicated in Fig.-Prob.17(b), calculate the value of the components RX and RY, the value of the reaction “R” and of the beta angle.- W is the weight of the arm, applied in the middle of its length.- R is the reaction at the shoulder joint O.- RX and RY are the horizontal and vertical components respectively of the reactionapplied at the shoulder joint O.- Note: Consider that the mass of each arm of the athlete is 3% of the total mass, and thatthe length of the arm is equal to 35% of its height. Fig.-Prob.17(a): Man performing the position of "The Christ"Fig.-Prob.17(b):…
Draw the free-body diagram of the uniform bar, which has a mass of 100 kg and a center of mass at G. The supports A, B, and C are smooth.
Assuming smooth contact surfaces, the weight of the small cylinder and big cylinder is 250 kN and 500 kN respectively. Determine the normal force at A, B, and D and reaction at C.
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)