28 Calculate the force components of the water acting on the deflecting blade shown inthe figure if the blade is stationary.2 in. dia.120 ft/sec60⁰If the blade is stationary,the force components of the water acting on the deflecting blade are;A. Rx 304.73 lb; Ry527.82 lb76.18 lb;131.95 lbB. RxC. Rx 1187.59 lb;D. None of the aboveRyRy = 685.65 lb

Answered: Image /qna-images/answer/ec2a48b7-6e94-41d1-a5e0-c43ceb2bd621.jpg

Calculate the force components of the water acting on the deflecting blade shown in the figure if the blade is stationary. 2 in. dia. 120 ft/sec 60° X If the blade is stationary, the force components of the water acting on the deflecting blade are; A. Rx = 304.73 lb; = 527.82 lb B. Rx 76.18 lb; Ry= Ry = 131.95 lb 1187.59 lb; Ry - 685.65 lb D. None of the above C. Rx

Calculate the force components of the water acting on the deflecting blade shown in the figure if the blade is stationary. 2 in. dia. 120 ft/sec 60° X If the blade is stationary, the force components of the water acting on the deflecting blade are; A. Rx = 304.73 lb; = 527.82 lb B. Rx 76.18 lb; Ry= Ry = 131.95 lb 1187.59 lb; Ry - 685.65 lb D. None of the above C. Rx

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
Calculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
1. How much work UP is done by the force P = 45 N on the collar?UP = _______N·m 2. How much work Ug is done by gravity on the collar?Answer: Ug = ______ N·m 3. Determine the speed of the collar as it passes position B.v =______ m/s
The 42 foot long overhanging beam shown is supported by a pin at A and a roller at C. The beam supports a point load of 42 kips at point B. Determine the slope at pin A, deflection at point B, and the slope and deflection at point D. Modulus of Elasticity, E = 10,000ksi, Moment of Inertia, I = 2500in4. Let slope and deflection be functions of x, with x positive to the right.
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
The 14.6 lb lever OA with 9.6 in radius of gyration about O is initially at rest in the vertical position (?= 90°) where the attached spring of stiffness k = 4.3 lb/in is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity ? = 5.9 rad/sec as the lever reaches the horizontal position ? = 0.
The rod by which slider A is attached is rotating along a horizontal plane. Its position is defined by θ = 1 /2 sin(π t) where theta and t are expressed in radians and seconds, respectively. The slider A slides along the rod so that its distance r=1+e ^2t, where r is expressed in centimeters. When t = 3 s, determine the magnitude of the velocity of the collar.
Consider two blocks connected . BlockA has mass 2.00 kg, and block B has mass 5.00 kg. The table on whichB sits is frictionless, the cord connecting the blocks is light and flexible,and the pulley is light and frictionless. The horizontal force F S hasmagnitude F = 20.0 N, and block B moves to the left with an accelerationof 1.50 m/s2. What is the coefficient of kinetic friction that one block exerts on the other?
A wooden circular board 1m in diameter is being submerged vertically in a liquid having SG=1.15. Its topmost part is flushed in the liquid surface. Use 9.81kN/m3 as the specific weight of water. Find the: a) total hydrostatic force (kN) acting on one side of the board b) the distance (m) of the center of gravity from the liquid surface c) the location of the center of pressure measured from the liquid surface in meters Note: Do not round off intermediate values. Answer in four decimal places and do not include units in your answers.
Calculate the value of the deflection at point B due to uniformly distributed load w in the form answer in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
'A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square lamina, of side 20cm and mass 0.5kg. A gardener holds the spade horizontally with hands 30cm and 60cm from the end of the rod. Find the vertical forces exerted by the gardener's hands.' Im having trouble answering this question, the answer is 21.7N and 3.3N.