Calculate the force generated in element 1 of the following truss if the forces A, B, and C are 1.335 N, 842 N, 516 N respectively.

Q: Example 2\ The vertical force P of magnitude 100 kN is applied to the frame shown in the figure.…

A: Resolve P into components parallel to the member Ab ;

Q: Consider the simply-supported overhang beam shown. There is a pin support at A, a roller support at…

A: Given beam is simply supported with overhang end.The length of span, L =10mthe loads are uniformly…

Q: Determine the components of the 2 KN force along the oblique axes a and b. Determine the projections…

A: Draw the line AB To find out the angle A, using the properties of triangle  ∠A+45°+15°=180°∠A=120°…

Q: Generate the stiffness matrix for the frame corresponding to three degrees of freedom 1, 2, 3 42 31…

A:

Q: Determine the horizontal displacement and rotation at D. The frame members have a 10cm x 1Ocm square…

A:

Q: Example The 30-N force P is applied perpendicular to the portion BC of the bent bar. Determine the…

A: P=30 N BC=1.6mAB=1.6m

Q: Compute the magnitude of the resultant of the two forces exerted by the two structural members on…

A: To determine the magnitude and the direction of the resultant of the given force system.   The given…

Q: 1. Use the force method to determine the horizontal reaction at support c of the frame below with…

A:

Q: 1) Draw the shear force and bending moment diagram of the beam in Figure Q2(a), (b), and (c). The…

A: Solution a) Solution Draw the diagram with reaction

Q: diagrams, (b) determine the equations of the shear and bending-moment curves. P B A D

A: SFD- Shear force diagram shows the algebraic sum of all the forces acting on the beam laterally.…

Q: A 2 m SN kN/m 6 m 45 B 3 m 3 m

A:

Q: Solve for the axial forces on members BC, BD, and CD. Use theta= 18 degrees.

A: Determine the axial forces in  FBC =? FBD =? FCD =?

Q: A rigid beam loaded with negligible mass is pinned at B and is supported by two identical rods,…

A:

Q: The uniform beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm? and 18…

A: Hello dear this is the solution of your problem The answer is found to be Force in the bar CD is…

Q: Determine the magnitude of the vertical displacement of joint C of the truss (in units of mm). Each…

A:

Q: The uniform 20-ft pole has a weight of 150 lb. and is supported at point B on the floor and at point…

A: Given- L=20ftW=150lb

Q: 2 kN 5 kN 400 mm 700 mm 300 mm Draw the diagram of internal bending moment

A:

Q: +y A B a +x 12 Three coplanar, concurrent forces at O Horizontal component of force B will act…

A:

Q: For the beam shown in the figure, if w = 355 N/m and d 2.2 m :Find the shear force at point C in (N)

A: Given - w =355 N/m and d = 2.2m To find - The Shear Force at C in (N)

Q: 3 kN/m A B. – 3 m – 3 m

A:

Q: 5. Analyze the statically indeterminate beam by force method, and draw the bending moment diagram,…

A:

Q: The plane truss is loaded as shown 10 N D. E B. 2.40 m 2.00 m 2.40 m 2.40 m 2.40 m What is the force…

A: To determine the force in member CD.   As we are required to determine the force in a specific…

Q: Determine the magnitude of the force F given that the moment about the axis BC is 600 N.m 4m B y F…

A: The given figure is shown below:

Q: 50 kN D 25 kN 15 kN 55° 55° 35° B A 5.0 m 2.6 m

A: Let,RA=vetical reaction at support A in upward directionRC=vetical reaction at support C in upward…

Q: Q.2) For the truss shown in figure below, determine the forces in lo00 TD 2000 N LE in 2/E to JE

A:

Q: 4. Determine the magnitude and direction with respect to the positive x-axis of the given forces.…

A: Determine the magnitude and direction of resultant with respect to the positive x-axis of the given…

Q: The signboard truss is designed to support a horizontal wind load of 800 lb. If the resultant of…

A:

Q: Draw the free-body diagram for the figure shown, then determine the tension forces in cables BA and…

A: This question is related to Engineering Mechanics. Using force equilibrium equation we calculate…

Q: 4. 4 point E having A shown in the figure has coordinates (6,4) determine coordinates (12.22) A(6.4)…

A: The Moment of a force is a measure of its tendency to cause a body to rotate about a specific point…

Q: D. D 1083 N

A: Data Given: Asked: Resultant force in member AB

Q: Determine the required magnitude (kN) of force F B. Determine the direction Ɵ (degrees) of force F…

A:

Q: 4. A force of 540N is directed from C towards E in the cube. a. Determine the moment about the…

A: Given data:   Force=540 kn   It is asked to determine: 1. Moment about x-axis 2. Moment about…

Q: 2. From the given overhanging beam below, calculate the location of maximum moment from point A and…

A:

Q: Find the combined moment of the forces P and Q about point O. The magnitudes of the forces are P=…

A: Moment about O Moment about OMO=xFy=120Moment about BMB=906-xFY=906Fy-xFy=90substitute…

Q: Compute for the forces on each member assuming that the triangles are equilateral

A:

Q: Civil Engineering Department 5. In figure 3, the Y component of force P is 938kn. Determine the…

A:

Q: 5m 10 m 2 5 m 10 m Sn

A: Given data  Load P Span member length Method of joints   Member 4 and member 5 are zero force member…

Q: For a cantilever truss shown, assume that the diagonal cannot carry compression. Determine the…

A: Truss : A truss may be a structure in engineering that "comprises of two members only, with the…

Q: An equilateral triangulated 2D truss as shown below is subjected to a load 20 kN at B. The force (in…

A:

Q: Q1. 1.5m 1.5m Referring to Figure Q1(a) until Figure Q1(e); (i) Check the stability and the…

A: Note: Hi! Thank you for the question. You posted multiple questions in one question. As per the…

Q: 800 N 1.2 m 500 N/m А 1.8 m B 1300 N/m

A:

Q: Determine the moment of the force 360 N about points A and B.

A: Given:- Force=360N To find:- Moment about A and B

Q: Express the 830-lb force F as a vector in terms of the unit vectors i, j, and k. Determine the…

A: Given :- Magnitude of the force F = 830 lb Point A = {-35,-23,17} Point B = {61,26,37}  To determine…

Q: Example 2\ The vertical force P of magnitude 100 kN is applied to the frame shown in the figure.…

A: To find the force in member AC and AB

Q: 12) The resultant force vector orientations are ° ;B = a=

A: To calculate the orientation of resultant force first we have to calculate the resultant force and…

Q: Elaborate the principle of statics to calculate the internal shear force and bending moment as…

A: Principal of statics: The principal of the statics is defined as the study of the structure with is…

Q: Problem 2 Determine the position of the resultant from support A when it intersects the bottom chord…

A:

Q: Determine the forces in all bars of the trusses in the figure. Indicate if bar forces are tension or…

A: Consider a section x-x as shown below. Consider the left-hand side of the section.

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.