Calculate the forces, in Newtons, for the following:(d) member FG(e) pin H(f) hydraulic cylinder AB 724A mechanism carries a constant load P applied to the seat asshown.For the angle 0, determine the following400E(a) the lengths LBE and LAB, in m(b) the angles a and 9, in degreesDraw the complete FBD of(c)members AB, FG, EBH and GHICalculate the forces, in Newtons, for the following(d) member FG(e) pin H(f) hydraulic cylinder AB100175LBEop os udeaThis is not yoproperty so do not upon anyway aswer your own150DE150C175B34.5 degrees200Dimensions in millimetersGHP = 724 N150This is not your propertyso do not use it in anyway as if it were your

Name: Calculate the forces, in Newtons, for the following:(d) member FG(e) p
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Calculate the forces, in Newtons, for the following:(d) member FG(e) pin H(f) hydraulic cylinder AB 724A mechanism carries a constant load P applied to the seat asshown.For the angle 0, determine the following400E(a) the lengths LBE and LAB, in m(b)

Given: The load, P = 724 N The angle, θ = 34.5°

Answered: Calculate the forces, in Newtons, for…

Engineering

Mechanical Engineering

Calculate the forces, in Newtons, for the following: (d) member FG (e) pin H (f) hydraulic cylinder AB

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at A. Draw the FBD for the bar, recognizing that it is a two-force body. Determine the number of unknowns.
A mechanism is used to apply a constant load Q to the seat in the manner illustrated. 1. Determine the following for the angle: - the lengths of LBE and LAB, in m - in degrees, the angles ? and ? 2. Compile the FBDs of members AB, FG, EBH, and GHI in their entirety. 3. Determine the forces involved in the following situations, in Newtons: - FG-member - H-pin - AB-cylinder hydraulic
One end of a post weighing 400 Nand with height h rests on a roughhorizontal surface with ms = 0.30.The upper end is held by a ropefastened to the surface and makingan angle of 36.9° with the post. A horizontal force F isexerted on the post as shown. (a) Ifthe force F S is applied at the midpointof the post, what is the largest value it can have without causing the postto slip? (b) How large can the force be without causing the post to slip ifits point of application is 6/10 of the way from the ground to the top of thepost? (c) Show that if the point of application of the force is too high,the post cannot be made to slip, no matter how great the force. Find thecritical height for the point of application.
Show complete solution & FBD. 3 decimal points. The boom ABC has a weight of 100 KN is supported by a pin at A and the cable BD. AB = 5 m andsegment BC = 2.0 m Draw the FBD and determine the tension T in the cable, if angle θ = 55o.
Determine the unknown forces by applying d’alemberts principle to a free body.
Determine the internal force on: Member FH, in lb Member GH, in lb Member EK, in lb
A triangular block shown is subjected to the loads S = 1000 lb and T = 2000 lbs. If AB = 8 in and BC = 6 in, resolve each load into components normal and tangential to AC.
The cable and boom system shown support a load of 555 N. Determine the tensile force T in the cable and the compressive force C in the boom.
Determine the internal forces at point K when a semicircular rod is loaded.
Figure 1: For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the frame. (2 decimal point, indicate the answer in kN. Ex: 3.87kN just encode 3.78)
Two double-threaded square power screws have root diameters of 2 in. each and pitches of 0.5 in. each. Both are arranged in parallel and areused to convey a load of W = 502 lbs using a motor that rotates at 300 rpm. Determine the force F for each screw (in N) applied at the end of a lever 3 ft long if these power screws lift the given load.
Determine (a) the compressive force in the bars shown after a temperature rise of 96oC, (b) the corresponding change in length of the bronze bar.