Calculate the instantaneous deflections and the long term deflections after four years, assuming that 30% of the live loads are continuously applied for 48 months, f'c = 28 mPa, fy = 420 mPa, bw = 400 mm, h = 600 mm, Compression bar = 28 mm diameter, Tension bar = 32 mm, DL = 23 kN/m and LL = 35 kN/m 65 bw 75

Calculate the instantaneous deflections and the long term deflections after four years, assuming that 30% of the live loads are continuously applied for 48 months, f'c = 28 mPa, fy = 420 mPa, bw = 400 mm, h = 600 mm, Compression bar = 28 mm diameter, Tension bar = 32 mm, DL = 23 kN/m and LL = 35 kN/m 65 bw 75

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 2.78 A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid supports as shown. For the type and grade of rubber used r =1.54 MPa and G=12.6 MPa. Knowing that a centric vertical force of magnitude P=13 kN must cause a 2.5-mm vertical deflection of the plate AB, determine the smallest allowable dimensions a and b of the block. 75 mm bnin = 56.3 mm = 20.5 mm a min
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 310 MPa, determine the minimum force P required to punch the slot. Punch 705 kN 660 kN 844 KN 904 kN O 772 KN Slug Plate 20 mm 75 mm Plan view of slug Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank View Que Multi Que Multip Que
Using the "Effects Overlay" of the original beam, using isostatic sub-beams and simulating them separately, the final deflection result of the sum of the 3 statically determined beams should be equal to the original beam deflection . Simulate the two overlapping beams separately. The carbon steel beam with a modulus of elasticity E = 200 GPa W = 2.5 ton/m P = 10 ton and it is at 1/4 L L = 20 m
Week: 3: Flexure: Behavior and Nominal Strength of Beam Sectio 3.6 The Working-Stress Design Method * Homework 1: Calculate the bending stresses for the section shown. Use M = 55 kN.m f'e= 27.6 Mpa 250 mm fy = 414 MPa 535 mm 600 mm As-1516 mm Ausinan atesser O anan ama
A 30mm diameter bar is 1.25 m long. When the bar is simply supported at its ends in a horizontal position and is loaded with a concentrated load of 370 N at mid span, the central deflection was found to be 9.50 mm. In the second case, the bar is placed vertically and loaded axiallyThe buckling stress (in N/ mm²) of the vertical bar is
For a Vicker's Test, find HV in MPa if applied force is 100kgf with impression diagonals are 10mm and 8.4mm, respectively
A bar of length L tapers uniformly from diameter 1.1 D at one end to 0.9 D at the other end. The elongation due to axial pull is computed using mean diameter D. What is the approximate error in computed elongation? [IES-2004] (a) 10% (b) 5% (c) 1% (d) 0.5% The stretch in a steel rod of circular section, having a length 'l' subjected to a tensile load' P' and tapering uniformly from a diameter di at one end to a diameter d₂ at the other end, is given [IES-1995] Pl pl.л 4 pl (b) 4Ed,d₂ Ed,d₂ Edd₂ (a) (c) pl.л 4 Ed,d₂ (d)
Problem 4: (P2, М3, Р3) Shaft design is one of the most critical tasks in any rotating machine. You work as a reliability engineer for an automation company and your boss asked you to validate existing design parameters of a rotating 0.015-m-diameter solid shaft and pully assembly, shown in Figure.5. This task can be performed by: Calculating the maximum torsional stress and deflection angle in the shaft. (P2) Find the torsional component of strain energy Utorsion: (M3) Use the torsional Castigliano's Theorem to evaluate the shaft's deflection. (M3) Use for Part 4 of the question only! 0.050 m 300 N В 0.250 m 200 N 550 N 0.250 m' 400 N 0.150 m D 0.075 m
If two closely coiled helical springs A & B with the mean diameter of spring A is half of that of spring B and having an equal number of active coils and same wire diameter are subjected to a same axial load of W, then the ratio of deflection in spring A to B. 1. 2. 4|11| 8 3.2 4.8 strength-of-materials springs
Calculation: Modulus of Rupture: 3PmaxL MR = 2bh² Apparent Modulus of Elasticity: PL³ E = (4) 4bh³ Pmax and L = maximum load and span of the beam b and h = width and height of the cross-section P = increment of applied load below proportional limit A = increment of deflection of beam's neutral axis measured at midspan over distance L and corresponding load P Note: The weight of the beam is not included in the above calculation. Where:
Q5. Determine the rod extension after tension test on a steel rod had the following results; Rod diameter = 30mm Rod length before test = 200mm Maximum applied load = 400KN Youngs modulus of elasticity = 25000N/mm %3D %3D
Problem III. Figure (a) shows a channel section that has an area of 3790 mm2 and its moment of inertia about the x and y axes are lx = 25.3 x 106 mm4 and ly = 1 x 106 mm4. Now, figure (b) shows a section where two of the same channel section in Fig (a) are riveted together. EI - 14.8 mm (a) (b) a) What are the moment of inertia about x and y axes of the composite section? b) Determine the radius of gyration about x and y axes. c) If the moment of inertia about the x-axis is to be transferred to an axis found at the topmost fiber of the composite section, what will be its value?