Calculate the interior angles for the following data given Table Q2, and also draw a neat sketch of the traverse. Enter the values of back bearings in the Table Q2. Table Q2 Line Fore Bearing         Back Bearing AB 60° 30’ BC 122° 0' CD 46° 0' DE 205° 30 EA 300° 0'

Q: The interior angles of a five side traverse are as follows: A=142°54' B=96°32' C= 117°30' and…

A: A curve, without sharp turns is a continuous and smooth line. The radius of curvature of the normal…

Q: For the given data of a close traverse, determine the missing bearings of course CD and DE solve the…

A: n

Q: Interior Angle Traverse Given the bearing of each line of a closed traverse ABCD, determine the…

A:

Q: Answer the following problem. For each column, provide only 1 solution. The solutions and answers…

A: Solution (a) Adjusted coordinates Line Distance (m) Azimuth  (south) Azimuth  (north)…

Q: Compute and tabulate the forward and back bearings and azimuths (from north and south) of a regular…

A: GIVEN Forward Bearing of line AB = 215° 25' 42'' Traverse is clockwise ? For Icosagan traverse, no…

Q: A Surveyor has Surveyed a line (Open Traverse) and Recorded the following results, the length and…

A:

Q: Find the true course to steer if the compass course reads N 36°W, deviation 17°W, variation 39°E. а.…

A:

Q: UPVOTE WILL BE GIVEN. Please write the complete solutions and box the final answer. Use 4 decimal…

A:

Q: Discuss the advantage and danger of radial traversing.

A: When using a total station instrument, radial traversing is suitable for swiftly creating a high…

Q: MOMENT AREA METHOD FIND THE SLOPE AT POINTS B & C E= 200GPA I= 360x106mm4 5m 10KN A 10m

A: Moment Area Method: Given: E = 200GPa=2 x 105 N/mm2 I = 360 x 106 mm4  EI = 7.20x1013 N mm2

Q: Please perform the analysis to find the elev of BM 2.  Also find the error, indicate the order and…

A:

Q: 4. An interior angle traverse as shown below was completed. Azimuth Aac = 90°. Find the azimuth of…

A: The bearing of the line is always below the angle of 90 degree that is calculate corresponding to…

Q: Differentiate between the following. a. Profile leveling and cross sectioning (with the help of…

A: Difference between  a) Profile levelling and cross sectioning will be  Profile levelling Among the…

Q: find out the included angles in a closed survey PQRSTP, the f

A: Below table gives the whole circle bearing of the observations: Line FB FB-WCB BB BB-WCB FB-BB…

Q: Calculate interior angles with bearings of a closed traverse ABCD as under. Also apply usual checks…

A:

Q: 1. From the field notes of a closed traverse show below, adjust the traverse. LINES BEARING…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: Fill in the necessary answers to determine the collimation error of a levelling instrument: B to E =…

A: Given:- L=65000 To Find:- error

Q: 521.96 ft. If a check of the rod after the work is done reveals that the bottom 0.04 ft has been…

A: Surveying is done as a priority in civil engineering before the building took place for…

Q: In the closed loop traverse given below find; b) Bearings (Bearing EA is 200° 30')

A: The bearing of a line is the angle between the line and the direction of the true north. The bearing…

Q: Three basic requirements determine an angle: (1) reference or starting line, (2) direction of…

A: Three basic requirements determine an angle: (1) reference or starting line, (2) direction of…

Q: The following bearings were observed in a close traverse. Find the included angles and correct the…

A: Declination = 4° 30 ' W AB = 90 m, BC = 90 m and CD = 60 m

Q: 1-Draw the profile section with (V.S. = 1/50 and H.S. = 1/2500). %3D 2-Calculate and draw the…

A:

Q: For the given data of a close traverse, determine the missing bearings of course CD and DE solve the…

A:

Q: QIA) The following are the bearings observed in traversing. Calculate the interior angles of the…

A:

Q: Using a table, cite and differentiate at least five (5) advantages and five (5) disadvantages (for…

A: Given , We have To differentiate 5 advantages and dis advantages of Both Compass rule and transit…

Q: A closed traverse has the following lengths and bearings: Line Length Bearing АВ 200.0m Roughly East…

A: The answer is found to be Length of CD =204.592 m Bearing of line AB =86.68°  For explanation please…

Q: An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from…

A:

Q: Problem 4 For the given data of a close traverse, determine the missing bearing of courses BC and…

A: To Determine The missing bearing of courses BC and DE. Solve the AREA using DPD and sketch the…

Q: Q1/ find the area of the close traverse which is shown in the below figure by (60 degree) 1- DMD…

A: Solution: Given: A = 0,10 B = 4,23 C = 13,18 D = 9,1 F = 6,13

Q: Laboratory Report 11 – Double Rodded Leveling Objective: To determine the elevation of BM12 using…

A:

Q: For the given data of a close traverse, determine the missing bearings of course CD and DE solve the…

A:

Q: For the given data of a close traverse, determine the missing bearings of course CD and DE solve the…

A: Given : Lines  Distance (meter) Bearing Latitude Departure DPD Double Area AB 32 S39°25'W…

Q: Following bearings were observed while running a closed traverse. Correct the bearing for local…

A:

Q: Q1: for the traverse in the table below: 1- Draw a sketch 2- Balance the angles 3- Compute the…

A:

Q: c) Determine the project control accuracy of the traverse. (Primary, Secondary, Tertiary, or "not…

A: (c) Here azimuth is given from south. converting it from north for easiness of calculation. Sample…

Q: For the given data of a close traverse, determine the missing bearings of courses DE and EF then…

A: Traverse is a technique in the field of reviewing to lay out control organizations. It is likewise…

Q: List the three basic requirements in determining an angle.

A: Angles are generated when two lines coming from a specific point intersect: an arc is a popular…

Q: A closed traverse has the following data. Find the bearing of line AB and BC.

A: Given data,  Length of line AB= 60m BC= 72.69m CD = 44.83m DE = 56.45m EA = 50m To find out the…

Q: 1. From the field notes of a closed traverse show below, adjust the traverse. LINES BEARING…

A: Latitude of a line is given by  L=lcosθand departure of a line is give by D=Isinθ where I and 8 are…

Q: determine the adjusted bearing lines of each surveying line and the back azimuth of FBab, FBbc, and…

A: There is a mistake in the question. The BBDA should be S 9040' E (otherwise answer won't match)

Q: Differentiate the meaning of compass rule and transit rule in adjusting a given traverse (in solving…

A: To give the difference between compass rule and transit rule in adjusting a given traverse.   Then…

Q: Q1/in the closed traverse with points ABCDA, the Azimuth of its sides are: AB=120° 14 BC=40° 20',…

A:

Q: 1. From the field notes of a closed traverse show below, adjust the traverse. LINES BEARING…

A:

Q: FROM THE GIVEN DATA OF A CLOSED TRAVERSE, FIND THE ADJUSTED BEARING OF BC AND DA USING COMPASS RULE.

A: From the above table we are determining the adjusted Bearing,The adjusted bearing of BCTha adjusted…

Q: List at least five (5) advantages and five (5) disadvantages of using the Trapezoidal Rule in…

A: ADVANTAGES the main advantage of the Trapezoid rule is its rather easy conceptualization and…

Q: For the given data of a close traverse, determine the missing bearings of courses DE and EF then…

A: Given :     Lines     Distance (m)         Bearing Bearing in WBC θ            Lcosθ…

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.