5) Calculate the magnitude and the position from point 'a' of the resultant load caused by the loading on thebeam.12 kN15 kN/m6 kN/me1.5 m-e3 m3 m6) Three ropes support the 400-lb crate as shown below. Determine the forces in ropes AB and BC if the third ropeis being pulled with a force, P = 460-Ib?60°B30°

Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Answered: Calculate the magnitude and the…

Calculate the magnitude and the position from point ´a' of the resultant load caused by the loading on the beam. 12 N 15 kN/m 6 kN/m e1.5 m 3 m 3 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.65P: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,...

See similar textbooks

Related questions

Q: Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect…

Q: Which of the following is the shear force diagram for the beam below. 12 kN/ m C 3 m 6 m

A: Let the support reaction at B and C are RB & RC. The reactions are calculated as :…

Q: 50 kN 45 kN 12 kN.m. 4m 4m 4m 4m

Q: Determine the maximum allowable intensity w of the uniform distributed load that can be applied to…

A: Given : Allowable bending stress = 165 MPa Solution :

Q: Draw the shear and bending moment diagrams for the bear 2 kN/m 5 kN m |A В 5 m

Q: QI:For the force system as shown in figures below ,Find the magnitude of the equivalent concentrated…

Q: A structural member is said to be slender when the dimensions of its cross section are its length O…

A: A structural member is said to be slender when the dimensions of its cross section are............…

Q: 1. Draw the Shear and Moment Diagram A В MA 10 kN/m 2 m

Q: Homework 1: Find the resultant of the distributed and concentrated loads as shown in the figure. 8…

Q: Determine the internal loads diagrams of the beam above. In the cell bellow give the value of the…

A: According to the details provided in the question, we need to calculate we need to draw SFD And BMD…

Q: Determine the value of Elv (in Ib ft³ ) at the section below the load P for the beam loaded by two…

Q: H.W3 Draw the shear force and bending moment diagrams for the beam shown below 5 kN/m M = 60 kN m 2m…

Q: termine the magnitude of the vertical force Cy for the simply supported beam, where w = 10 kips/ft,…

A: Ans: 38.5 kips

Q: The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m…

Q: 15 kN/m 10 kN 10 kN 60° A D B C 2 m 1 m lm

Q: A 5-m-long simply supported timber beam carries two concentrated loads as shown. If L = 28 kN and M…

Q: Replace the loading acting on the beam by a single resultant force. Specify where the force acts,…

Q: A beam of length L = 22 in supports a load which varies from w = 20 lb per ft at the right end to…

A: Find the position of resultant force from left end for the triangular load.

Q: 10.0 10.0 M 10.0 10.0 N. 10.0 10.0 10.0 A F G

Q: 05: Find the magnitude, location and slope of the resultant of the non-concurrent coplanar force…

Q: Determine the value of Elv (in Ib ft³ ) at the section below the load P for the beam loaded by two…

A: Let the pin end be "A", point at which load P acting is "B", point at which load Q acting is "C"",…

Q: Resolve the forces shown in the Figure below to two components Fx and Fy

A: The expression for the angle made by force F2 with the horizontal can be written as below,…

Q: 2. Compute the midspan value of Ely for the beam loaded below 600 N/m 1 m 3 m 2 m R1 R2

Q: 02. If R is the resultant of the forces P and Q, find P and Q. J30 25° SUMMARY OF ANSWERS R= 360 lb…

A: Given data To determine The value of P and Q

Q: 3. Determine the most unfavorable arrangement of the crane loads and compute the maximum and minimum…

A: given data; ⇒reaction force at point A=RA⇒reaction force at point B=RB

Q: Draw a free-body diagram of the crate that has a center of gravity at G. (Figure 1) Draw the vectors…

Q: mathal 220 N/m 890 N/m 6 m Figure P-238

Q: if the Resaltant For Forces shownin figure equal To ClooN) upward, find F pO;? 450N 300 N

Q: 6 kN 6kN/m 4 m 2m

Q: AP 12 kips 48 kip. ft B C 4 ft4 ft 4 ft D

Q: the load of 6 kN/m has been changed to 11 kN/m, • the central length of 2 m has been changed to 4 m…

A: Given: w=11 kN/ml=6 m Solution: let The resultant is acting at x distance from point A. The…

Q: 20 kN/m 2m 2m 60 kN M = 120 kN-m 2m 2m R₁ R₂ What is the maximum moment (KN-m) value from the beam…

Q: Replace the force system acting on the post by a resultant force. * 0.5 m B- 500 N 1 m F0.2 m 250 N…

A: Given data: - The force one is F1 = 250 N. The force two is F2 = 500 N. The force three is F3 =…

Q: 5 m 150 KN B 5 m

Q: w = 40 kip/ft w = 20 kip/ft a L = 30 ft

A: Dividing the load in two parts and then solve for the following

Q: Replace the loading acting on the beam by a single resultant force. Take F₁ = 450 N, F₂ = 290 N, F3…

A: Given Force, F1 = 450 N F2 = 300 N F3 = 700 N Moment, M = 1500 N.m Find…

Q: 400 N/m 200 N/m B 8 m

Q: Write shear and moment equations and draw the shear and bending-moment diagrams for the beam. Given:…

Q: Q1) The rope tension in OA is 750 N, which prevents the beam from rotating around O. Calculate the…

Q: The beam AB supports a load which varies from an intensity of 80N/m to 250 N/m Calculate the…

A: HERE,in the given problem length of the beam is not given, so assume 6m.

Q: 10. Determine the magnitude of the hydrostatic force acting on gate AB, which has a width of 2 ft.…

A: Given:w=2 ftγw=62.4 lb/ft3

Q: The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 16.2 mm,…

Q: Find the maximum moment of the beam loaded as shown. Express your final answer in Ib.ft to the…

A: Draw the shear force and the bending moment diagram for the following beam

Q: The beam AB supports a load which varies an intensity of w1 = 6 N/m to w2 = 12 N/m.

Q: 5) Compute the value of EI y at the right end of the overhanging beam shown 1000 lb 400 lb/ft 6 ft 4…

Q: Determine the maximum shear and moment for the beam shown below. 1000 lb 400 lb/ft В C A +2 ft→ - 4…

Q: Calculate the position of the resultant load from point A in meters.

A: W1= 6 N/m W2= 12 N/m

Q: 2) Determine the moment of Area of the given Built-up section about its centroidal axis.The top…

A: In order to find the moment of area of the given cross-section we have to divide the given…

Q: Draw the bending moment and shear force diagrams for the beam shown below. 60 kN 40 kN/m 5m 2.5m

A: It is required to draw SFD and BMD of given beam

Question

5) Calculate the magnitude and the position from point 'a' of the resultant load caused by the loading on the
beam.
12 kN
15 kN/m
6 kN/m
e1.5 m-e
3 m
3 m
6) Three ropes support the 400-lb crate as shown below. Determine the forces in ropes AB and BC if the third rope
is being pulled with a force, P = 460-Ib?
60°
B
30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 110-lb traffic light is suspended from two identical cables AB and BC, each weighing 0.80 lb/ft. If the maximum allowable horizontal force exerted by a cable on a vertical post is 170 lb, determine the shortest possible length of each cable and the corresponding vertical distance h.
Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero, compute (a) the maximum tensile force in the cable; and (b) the length of the cable.
The two main cables of the Akashi Kaikyo suspension bridge in Japan have a span L=1990m and a sag H=223m. The loading on each cable is w0=444.7kN/m (without traffic) along the horizontal. Determine the corresponding maximum force in one of the cables.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions l1 = 0,31 m ja l2 = 0,23 m Determine the support force on the rear tire.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the support force on the rear tire.
The platform scale consists of a combination of third and first class levers so that the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If a 3kg counterweight S is used to balance a 120kg load L, what is the value of 'x'? Draw all pertinent FBDs. Use g=9.806 m/s2.
A 30 kg barrel is sitting on a handcart as shown below. Determine the normal forces at A and B. Please show all work and drawl FBD
SITUATION 7: Three forces P1, P2, and P3 are acting on a semi-circular structure as shown in Fig. THA-33. Support at A is hinge and support at B is roller. Given: a = 1 m; P1 = 1.8 kN; P2 = 0.9 kN; P3 = 0.45 kN; θ = 30⁰; β = 45⁰. Calculate the resultant of the three forces (in kN). (Answer: 2.45) Calculate the vertical reaction at B (kN). (Answer: 1.06) Calculate the reaction at A. (Answer: 1.63)
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
Q1) Find the force F on the bottom of the tank if : K=1.5 m , H= 6 m, D=5 m.
In the system shown, take F1 = 20kN, F2 = 40kN. a-) Calculate the force P that will keep the system in balance b-) Calculate the resultant force at the C point.
A force of P=280 N is applied on semicircular rod at point B. Determine internal forces at point J if θ=30°. (draw free body diagram)