Calculate the maximum tensile and compressive stresses in the brass and aluminium.

Q: Give an example of the complicated stress distribution?

A: When any material is subjected to external load then stresses are induced in the material. These…

Q: One piece is made of a metal alloy with a yield limit of 180 MPa. At a certain point in the part…

A:

Q: Which material/metal is the stiffest based on the following data provided and why?

A: Concept: 1) Stiffness is ability of material to resist deformation against applied load.  2) For the…

Q: Distinguish between simple and indirect shear stress?

A: Simple shear stress also known as direct shear stress is the shear stress developed due to a…

Q: I have plotted Force vs Stress graph. I want to know: 1- What does the slope represent and what…

A: Here we have Stress on y axis and Force on x axis. We need to draw one trendline (Line of best fit)…

Q: A gauge # 10 HSLA steel for an automotive application has a Young’s modulus of 200 GPa, a yield…

A: Find the punch force required

Q: Calculate the reliability if information about both the strength data (170 ± 20 MPa) and stress data…

A: Given: The standard deviation based on strength data = 2x20 = 40 MPa The standard deviation based on…

Q: Give an example of a flexure formula?

A: The flexure formula is also known as the flexure bending equation and is defined as; Where, M is…

Q: Summary the properties that obtained from the engineering stress and engineering strain

A:

Q: Sketch the relationship between the stress and the number of cyclic loading applied on an element

A:

Q: From the following figure shows the tensile stress- strain curve for a plain-carbon steel. What is…

A:

Q: Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and…

A:

Q: Define the term Stress Concentrations?

A: Stress concentration is a location in a member under load where the magnitude of stress is…

Q: Define about the Selection of Shear Strength Parameters ?

A: Stability analysis of a rock slope requires an assessment of shear strength parameters, that is,…

Q: 6.Explain with the aid of diagram three different hardness tests and mention the hardness measure of…

A:

Q: calculate temperature change that will cause a tensile the stress of 90 MPa in the brass rod.

A: Given: Tensile stress =90 MPa To determine: The change in temperature

Q: explain linear stress variations,

A: As per Hooke's law in any material the stress induced is directly proportional to…

Q: How can we calculate the maximum stress?

A: Stress: Stress is defined as the developed force in the specimen per unit area when that specimen is…

Q: find the axial strain

A: Given; Young modulus =100 GPaPoisson's ratio=0.3 Find axial strain of the container material ?

Q: Figure below shows a stress-strain diagram. Explain this curve using your own words and define…

A:

Q: Suppose a 24 in. long round bar is to support a load of 400 lb. without any permanent deformation.…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Give an example of complicated stress?

A: Stress: When a body is subjected to a force/load, it develops an internal reaction in order to…

Q: What is Multiaxial Stress and explain with example?

A: When the various external loads are acting on a machine structure then in that case there are…

Q: (a) Draw two Engineering Stress - Engineering Strain graphs: one for a ductile metal and one for a…

A:

Q: From the tensile stress-strain behavior for the brass specimen the diameter is 12-8 mm Calculate the…

A: Please find the solution below.

Q: define stress and positive stress. causes of stress,

A: Given question: Define stress, Positive stress and causes of stress.

Q: Describe the Maximum Shear Stress Theory?

A: According to Maximum Shear stress Theory or Tresca's Theory of Failure: "A component subjected to…

Q: What is Shear Stress and explain with example?

A:

Q: Discuss the variations in nature of the stress-strain graphs of steel and aluminium.

A:

Q: Calculate the allowable (ASD) tensile strength of a WT125X22.4 with a transverse weld to its flange…

A: INTRODUCTION: There are two types of weld joints: fillet weld and butt weld. The fillet weld is…

Q: Why fracture strain for metals (Aluminum, Mild Steel) in pure share is higher than pure tension?

A: fracture strain for metals (Aluminum, Mild Steel) in pure share is higher than pure tension because

Q: A 96 kN load is applied to a 5 cm diameter, 3 cm tall, steel cylinder. Calculate the stress. Report…

A:

Q: Fatigue life of a material is higher if it has,

A: The fatigue life of a material can be defined as the number of cycles that can be sustained by a…

Q: d) If the critical resolved shear stress for yielding in silver is 240kPa, calculate the tensile…

A: Given Dataσcrs=240kPaslip direction =0 1 0

Q: Compare full stress-strain curve for steel, brass, copper and aluminium alloy.

A: Data given - Stress v/s strain graph for tensile loading

Q: and nature of stresses

A:

Q: Where is maximal torsional stress experienced?

A: The maximum shear stress is experienced at a section where the applied torque is maximum. This…

Q: Describe the material behavior of Steel

A: Material behaviour of steel 1. Ductility: The ductility of steel can be changed by changing the…

Q: Define Tensile strength.

A: Given Data⇒ Tensile strength Problem statement⇒ Problem says Define Tensile strength.

Q: Define the term Stresses on Arbitrary Plane?

A: In general, we can define the stress vector acting on an arbitrary plane with direction cosines la1,…

Q: An aluminum bar has the desired length when at 12°C. How much stress is required to keep it at this…

A:

Q: (a) Briefly explain the state of plane stress and plane strain.

A: Dear Student Kindly Check Two Stages For Complete Explanation. Stage 1: Plane Stress

Q: Compare between hot and cold working of metals.

A: To compare: The hot and cold working. Explanation: Hot working: This process is done above the…

Q: Write different types of stresses that a material can be subjected to? (

A: There are different types of stresses depending upon the direction and their distribution. The…

Q: When an elastic material is subjected to normal stress, what would thestrains that are produced…

A: The strain is the response of a system to applied stress. When a material is loaded with a…

Q: What is Multiaxial Stress?

A: Multiaxial stress states due to the action of various external loads exist at the considered point…

Q: Explain the relation of stress transformation in detail with diagram.

A: Draw a block showing 3D stress state into 2D stress state as given below. Here σx, σy, and σz are…

Q: What is thermal gradient in thermal stress [explained thoroughly]

A: The temperature gradient is defined as the difference in temperature between two points over a body.…

Q: lasticity, el

A: solution of above question is below