Calculate the natural circular frequency of the frame shown in figure. Compute also natural period of vibration in two conditions. A) Consider just Tension and eliminate compression effect. B) Consider Tension and compression effect equally (Same in tension and compression). m= 256 x 10 kg EA ko =T cos? a E-200 GPa A-10 em

Calculate the natural circular frequency of the frame shown in figure. Compute also natural period of vibration in two conditions. A) Consider just Tension and eliminate compression effect. B) Consider Tension and compression effect equally (Same in tension and compression). m= 256 x 10 kg EA ko =T cos? a E-200 GPa A-10 em

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A steel bar 25 mm wide and 50 mm deep is simply supported at two points 3 m apart andcarries three loads of 1000 N, 1500 N and 750 N at 1 m, 2 m and 2.5 m from the leftsupport. The Young's modulus for steel is 200 GPa. If the mass of the bar is 262 kg/m,find the frequency of transverse vibration.
Find the natural frequency (in Hertz) of the system illustrated in the following figure. Consider the length of the beam as L, flexural rigidity of the beam as EI and assume K1=105 N/m, K2=243 N/m, K3 =311 N/m, M=0.01 kg and EI = 500L^3/3
Find the natural frequency (in Hertz) of the system illustrated in the following figure. Consider the length of the rigid bar as 2L and assume K1=4,659 N/m, K2=5,977 N/m, M=0.6 kg, L=0.5 m and g=9.81 m/s2.
In the undamped single storey sliding frame given in the figure, rectangular section columns are has. Column section dimensions are given in the table. E = 1.5x107 kN / m2 and g = 10m / s2 will be taken. (25P) a) Calculate the stiffness of each column. b) Calculate the natural vibration period and angular frequency of the system. k1=column1:40x40cmxcm k2=column2:30x30cmxcm k3=column3:35x35cmxcm w:238kN h:3.05m
A torsion dynamometer is fitted on a turbine shaft to measure the angle of twist. It is observed that the shaft twists 1.5° in a length of 5 metres at 500 r.p.m. The shaft is solid and has a diameter of 200 mm. If the modulus of rigidity for the shaft material is 85 GPa, find the power transmitted by the turbine.
A solid steel shaft 4.5 m long is stressed at 75 MPa when twisted through 4.5°. What power can be transmitted by the shaft at 25 Hz? Use G = 83 GPa.
Plz give right answer. Calculate critical frequency of a helical spring of wire diameter 10 mm, mean coil diameter 50 mm and number of active coils 12. Take t = 550 MPa, G = 80 kN/mm².
The crankshaft-flywheel assembly of a large engine may be considered a torsion pendulum. The shaft is 1.8m long and transmit 179.127kN-m torque corresponding to 83MPa stress. The flywheel diameter is 75cm and weighs 4.5kN. If the modulus of rigidity of the shaft material is 77GPa, compute the period of vibration of this system.
A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress τmax in the shaft? (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter dmin of the shaft? A solid circular bar of diameter d = 50 mm is twisted in a testing machine until the applied torque reaches the value T = 500 Nm as shown in Fig.4. At this value of torque, a strain gage oriented at 45 ° to the axis of the bar gives a reading ε =339 ×10-6 . What is the shear modulus G of the material?
An assembly of rods is composed of a rectangular rod and a square square tube according to the figure below. The unit is loaded with the torque M. The yield strength is 310 MPa, the modulus of elasticity 210 GPa and the transverse contraction number 0.31 in both the square tube and in the rectangular bar. Dimension the unit, i.e. determine dimension a so that a flow safety of at least 1.5 is achieved. Also calculate the total distortion if L is set to 10 · a. The torque M is 10 Nm. If you want, you can check the result via Inventor's calculation module. Dimensions a start and end from the middle of the square beam goods (center to center).
A coffee table has a rigid top of mass 17 kg mounted on legs of total stiffness 38 MN/m and a damping coefficient of 1.6 kN/m/s. The coffee table is subjected to a vibrating force of 100 N. caused by sound waves from a nearby loudspeaker. Find the resonant frequency of the table, suggest a method to avoid the resonance for this table. Please provide a detailed solution. Thanks!!!