Please answer all aligned with our honor code. I. FREE-BODY DIAGRAM. Identify and show-in-detail the necessary force reactions to theidentified Mechanical Body. Observe proper angles and distances if the figure permits.EACH)1. A 2-kg homogenous barrel held by ropeA whilst pinned e B12002. A 7-kg homogenous cylinder held e restby smooth planes and by the two smallercylinders.3. A 5-m long uniform beam of mass 20 kgsupporting a distributed load while beingheld static by a pin and a cable that runsover a smooth pulley.4. A crowbar used to remove an embeddednail from a rough wooden block.

given; mass of barrel (m)=2kg lets take normal reaction between barrel and inclined surface=N…

I. FREE-BODY DIAGRAM. Identify and show-in-detail the necessary force reactions to the identified Mechanical Body. Observe proper angles and distances if the figure permits. EACH) 1. A 2-kg homogenous barrel held by rope A whilst pinned OB

I. FREE-BODY DIAGRAM. Identify and show-in-detail the necessary force reactions to the identified Mechanical Body. Observe proper angles and distances if the figure permits. EACH) 1. A 2-kg homogenous barrel held by rope A whilst pinned OB

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.51P: The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest...

See similar textbooks

Related questions

Q: A diverging tube discharges water from reservoir at a depth of 10 m below the water surface. The…

A: Depth, H= 10 m Throat diameter, D2= 150 mm= 0.150 m Outlet diameter, D3= 225 mm= 0.225 m To find:…

Q: Find the angle at which the compound rest is to be swivelled or set with the following data: a)…

A: Answer: The angle at which compound rest is to be swivelled is 7.125°.

Q: Select suitable materials for making insulated electric wire Insulators:

A: Insulated wire or cable is made of a non-conductive or electrically resistive substance. It…

Q: 3. Determine the maximum shear and moment_for the beam loaded as shown. Use any of the two methods.…

Q: 14-73. The roller coaster car has a mass of 700 kg. including its passenger. If it is released from…

A: Find the minimum height of the hill and normal reaction at B and C.

Q: 14-49. The 2-Mg car increases its speed uniformly from rest to 25 m/s in 30 s up the inclined road.…

Q: (CLO-4] A rigid tank initially contains 50L of air (Ideal gas) at 400 kPa and 25°C. A wheel…

A: GivenP1=400kPaT1=25oCV=50L=0.05 m3W=-150kJ -ve sign for work is done on the systemQ=-30kJ -ve sign…

Q: An aluminum ball of 5 cm diameter and a temperature of 95 deg C is being immersed into a mixture of…

A: Given For alluminiumd=5cm=0.05mTAl=95oCCAl=0.902 J/gK=0.902 kJ/kgKFor…

Q: To compute the average-end area volume, you need to know the distance (L) between the stations of…

A: The average end area calculation is used to get the volume between two cross-sections. Two…

Q: In an actual Rankine Cycle steam fArst enters the turbine at 10 Mpa and 400C. It expands to a…

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: Problem 2: What is the shear flow along the connected surface of the beam below? The Shear at the…

Q: Q1 /Draw S.F.D and B.M.D 20 N/m 100 m 3m 1m 6m Gm Shear Force Diagram S.F.D B.M.D

A: Given Data The UVL acting on the beam is: 50 kN/m The UDL acting on the beam is: 20 kN/m The…

Q: 1. The overhead electric hoist C rides along a track on the horizontal beam AB. In addition to the…

Q: A particle, originally at rest and located at point (3 ft, 2 ft, 5 ft), is subjected to an…

Q: 2. Water at 80 ° F, flows at a rate of 4.30 ft/s in a pipe having an inlet diameter of 1.0 inch…

A: Given: Volume flow rate of the water in pipe at section1: →Q=4.30 ft3s diameter of the pipe at…

Q: A two-stage rocket is fired vertically from rest at s=0 with the acceleration as shown. After 30 s…

A: Solution; from a-t graph: for 0<t<30: a=1230ta=0.4t fot t>30 a=24

Q: Q2) Consider a mass (m=5 kg) connected to a massless rod of length (L=2 m) to swing about point O,…

A: Given: mass, m=5 kgmassless rod length, L=2 mspring stiffness, k=10 N/mspring length, l=1 m

Q: A copper rod 6cm in diameter is placed within a steel tube, 8cm external diameter and 6cm internal…

A: Given Data The diameter of the solid copper bar is: Dcu=6 cm=60 mm The external diameter of the…

Q: The 10-lb collar starts from rest at A and is lifted by applying a constant vertical force of F = 25…

A: Given: The mass of collar, m = 10 lb The vertical force, F = 25 lb The angle, θ = 60°

Q: A crate of mass 62 kg is pushed along a floor with a force of 20 N for a distance of 5 m. Calculate…

Q: Select one: O a. [012]

A: Option B is the correct answer indices = [121]

Q: Draw the shear and moment diagram for each problem Use Method of Section (as Solution A) and Method…

A: SFD and BMD

Q: Car A is traveling at a constant speed of 96.5 km/h along a straight road, and car B is traveling at…

Q: 76. All surfaces of an infinitely lang heating element, having a cross section in the shape of a…

A: Given Thermal conductivity, k = 35 W/m.K Temperature, T1 = 400C…

Q: Describe the general process used to calibrate a device such as a pressure gauge or a temperature…

A: Pressure guage is a mechanical instrument use to measure pressure of a fluid medium. General time of…

Q: The figure below shows a river scow. The scow floats with submerged. The center of gravity is at…

A: Given data as per the question X =4 m H =10 m L =25m

Q: 14-91. When the 5-kg box reaches point A it has a speed v = 10 m/s. Determine how high the box…

A: Find the normal reaction and acceleration of the box.

Q: 5. Assume 5 lb of an ideal gas with R = 38.7 ft-b/lb-<R and k = 1.668 have 300 Btu of heat added…

Q: 2. Air at 40 °C moves over a long flat plate with a uniform free stream velocity of U = 900 m/s.…

Q: If the power generated from a wind system at a height of 50 meters is equal to 3O kilowatts at a…

A: Givencase 1H=50mP=30kWV=4m/scase 2P2=1.5P=1.5×30=45kWV2=2V=2×4=8m/s

Q: traveling forward at 25 m/s. The bed is loaded with boxes whose coefficient of friction with the bed…

Q: the Otto Cycle has a compression ratio of 10/1. At the beginning of the compression stroke the…

Q: Helium is compressed isothermally from 14.7 psia and 68°F. If the compression ratio is 4, calculate…

Q: 2. Using the area method, draw the shear and moment diagram of the beam loaded as shown. 8 KN/m 12…

Q: The assembly in Figure consists of a light rigid bar AB, pinned at O, that is attached to the steel…

Q: For demand function Q, = a-bP and supply function Q, = dP-c , using Cramer's rule determine…

A: Request work addresses the connection between the amount requested for a product (subordinate…

Q: A tank is full of water and open at the top. There is a frictionless nozzle near the bottom (30 feet…

Q: Q3/ An average person generates heat at a rate of 84 W while resting. Assuming one-quarter of this…

Q: Determine the corrected flow in pipe BE of the pipe network shown. Use f=0.012 for all pipes and…

Q: Q. for case 3 the end of the fin is insulated so that dT/dx=0 at x=L. and then e-mx emx 1+e-2mL…

Q: On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The lenght…

Q: Q2/ Suppose we are told that the acceleration a of a particle moving with uniform speed v in a…

A: Given data The acceleration of particle - aUniform velocity of particle- vradius of circle - rmass…

Q: Determine the horizontal and vertical components of reaction at the supports A and C.

Q: I = 0.80 A t = 3 hour = 3x 60× 60 = 10800 sec 3 3х 60х60 Now, t Q = I t =( 0.80 ) ( 10800) = 8640 C…

A: Given DataI=0.80At=3hrs Here we are computing the Charge and Number of electrons

Q: Solve the differential equation (6х2 — 10ху + 3у?)dx + (-5x2 + 6ху — Зу? )dy %3D 0

Q: Calculate the y- and z- coordinates of the point at which the resultant of all the forces acting on…

Q: The material hoist and the load have a total mass of 600 kg and the counterweight C has a mass of…

Q: Problem 3. Solve for the centroid (X, 7) of the shaded area shown below using the composite body…

A: Find the location of centroid.

Q: (PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare…

A: Feedback Solution (1): This feedback control starts with a level transmitter that will measure the…

Concept explainers

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.

Question

Please answer all aligned with our honor code.

I. FREE-BODY DIAGRAM. Identify and show-in-detail the necessary force reactions to the
identified Mechanical Body. Observe proper angles and distances if the figure permits.
EACH)
1. A 2-kg homogenous barrel held by rope
A whilst pinned e B
1200
2. A 7-kg homogenous cylinder held e rest
by smooth planes and by the two smaller
cylinders.
3. A 5-m long uniform beam of mass 20 kg
supporting a distributed load while being
held static by a pin and a cable that runs
over a smooth pulley.
4. A crowbar used to remove an embedded
nail from a rough wooden block.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The homogeneous 80-kg sign is suspended from a ball-and-socket joint at O, and cables AD and BC. Determine the forces in the cables.
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) Calculate the moment reaction at A. (ANSWER: 28.499) Calculate the total reaction at A. (ANSWER: 22.192) Calculate the vertical reaction at E. (ANSWER: 25.223)
A 10 m steel beam of mass 1000 kg extends 4 m beyond the edge of a flat roof. If a 2,000 kg object is placed on the beam 2 m beyond the roof edge and then to balance the beam a load of 750 kg must be placed on roof at _____ from the edge.
The hanging mobile pictured above consists of two masses, m1 and m2, suspended from a uniform 10 cm long rod, which is in turn suspended from the ceiling at an angle of 70 as pictured above. The mass m1 is 0.02 kg, while the mass of the rod is mr = 0.01 kg. Assuming the mobile is in a state of static equilibrium, find the value of mass m2.
A uniform pole of 2.5m length and 4.0kg mass is suspended horizontally fromthe side of a building where it is affixed with a hinge. It is held in place by awire that extends from the unattached end of the pole at an angle of 53 degrees andattached firmly to the wall. A 10.0kg mass is hanging from the end of the poleas well under the influence of gravity.a. Draw a picture of the situation.b. Draw a comprehensive free body diagram showing the force on the wire,the mass, the pole, and both the horizontal and vertical forces on thehinge.c. Use the hinge as the axis of rotation and balance the vertical torques anddetermine the tension in the wire.d. Use inertial dynamics to find the horizontal and vertical forces on thehinge.
The mechanism shown consists of a crank (bar AB), a connecting rod (bar BC) and the piston C that slides on the smooth surface (without friction). The combustion of gasoline produces a force P on the piston and this is kept in equilibrium with the moment M applied in A. The length of the crank is 116 mm, the length of the connecting rod is 183 mm, the force P is 710 N and the angle theta is 0.56 radians. Determine the value of M in Nm.
The homogeneous 25 kg bar AB is supported by a ball-and-socket joint A. End B, which leans against a frinctionless vertical wall ,is kep from sliding by the horizontal force D. Determine P and the force exerted by the wall at B.
An athlete of 60 kg and 1.70 m tall performs the ring exercise called "the Christ", in which he keeps his body immobile with his arms extended horizontally as shown in Fig.-Prob.17(a). The angle with the vertical of the cords from which the rings hang is theta = 10. (a) Determine the tension T in the cords holding the rings. (b) Considering each arm of the athlete as a rigid horizontal bar subjected to the forces indicated in Fig.-Prob.17(b), calculate the value of the components RX and RY, the value of the reaction “R” and of the beta angle.- W is the weight of the arm, applied in the middle of its length.- R is the reaction at the shoulder joint O.- RX and RY are the horizontal and vertical components respectively of the reactionapplied at the shoulder joint O.- Note: Consider that the mass of each arm of the athlete is 3% of the total mass, and thatthe length of the arm is equal to 35% of its height. Fig.-Prob.17(a): Man performing the position of "The Christ"Fig.-Prob.17(b):…
a 700 kg piston initially held in place by a renewable latch above a vertical cylinder
Determine the additional mass required for stable equilibrium. Meter stick: xcm = 50.0 cm, m = 150.0 g. Hanger clamp: x = +0.0 cm, m = 16.5 g. (see the figure below)