Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm outside diameter, 0.9 m long. The pipe surface temperature is 145 ° C, and the air temperature is 40 ° C. Convection coefficient = ... W / m² ° C.

Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm outside diameter, 0.9 m long. The pipe surface temperature is 145 ° C, and the air temperature is 40 ° C. Convection coefficient = ... W / m² ° C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.27P

See similar textbooks

Related questions

Q: heat and mass transfer An uninsulated steam pipe of 100-mm diameter is routed through a building…

Q: A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for…

Q: An Aluminum flat plate has a continuous and smooth surface over which the air flows at 2 m/s. The…

A: Given, V=2 m/s, length of each part, l = 10 mm, width, w = 0.2 m Ts = 500 ºC, T∞ = 25 ºC For air at…

Q: Water at a temperature of T∞ = 25°C flows over one of the surfaces of a steel wall (AISI 1010) whose…

A: Given data Ks=61W/mkT=110+502=80=353kKf=0.628w/mk

Q: Hot water at 50 °C is routed from one building in which it is generated to an adjoining building in…

A: Given:

Q: (a) Obtain expressions for the fin heat transfer rates, qso and q,1, in terms of the base…

Q: In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C…

A: Given: The dimension of solar plate : 1 m wide and 4 m long. Initial spacing between plates = 40 mm…

Q: (a) What will be the convection heat transfer coefficient for a similar bar with L = 1 m when V = 15…

A: The initial velocity of flow is V1=20 m/s. The convective heat transfer coefficient when velocity is…

Q: The walls of a refrigerator are typically constructed by sand- wiching a layer of insulation between…

A: Given: Inside temperature (T∞,i)=4°COutside temperature…

Q: In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C…

Q: for COVID vaccine. The volume of the storage container will be 1 m³. You are debating on three…

A: (a) Write the coefficient of heat transfer of air at velocity of 0.8 m/s.…

Q: wo heat reservoirs with respective temperatures of 325 and 275 K are brought into contact by an iron…

A: Given Thermal conductivity, k = 79.5 W/m K Temperature, T1 = 325 K…

Q: Suppose that a finned surface is exposed to an environment with a temperature of 32 and a…

Q: Find out the diameter of the spherical product being frozen in an air-blast wind tunnel. The initial…

Q: An uninsulated steam pipe is passed through a room in which air and walls are at 25°C. The outer…

Q: Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you…

A: Given: d= 1 ft L= 6 ft surface temperature=78 F h=2 Btu/hr emissivity=0.9 To determine heat transfer…

Q: A solid copper sphere (k = 393 W/mK), 10 mm in diameter, initially at 800C is placed in an air…

Q: vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for…

Q: Consider two aluminum (k=180 W/mK) pin-fin heat sinks with 1 mm and 2 mm square pins both 25 mm…

A: Amount of conduction or convection or radiation in an object decides or predicts the amount of heat…

Q: Air flows at 120 °C in a thin-walled tube (k = 18 W/m °C) with h = 65 w/m²- °C. The inside diameter…

Q: A stainless steel tube (k = 14,2 W / m.K) used to transport a chilled pharmaceutical has an inner…

A: The heat exchanger is a device used to transfer heat from one fluid to another fluid. For heat…

Q: A hot plate 1.2m wide, 0.35m high and at 1 is · Calculate the following Local heat transfer…

A: Given Wide = 1.2 m Height = 0.35 m To find Local heat transfer coefficient Average heat transfer…

Q: An uninsulated steam pipe of 100-mm diameter is routed through a building whose walls and air are at…

A: GIven:L=1 md=100 mmTa=27°C =300 KTs=147°C =420 Kh=10W/m2Kε=0.8Surafce area,A=πdLA=π*0.1*1 =0.314…

Q: Air at 4 °C is being carried within a metal cylindrical pipe to a storage room at a bioprocessing…

Q: Circumferential fins of constant thickness of 1 mm are fixed on a 60 mm pipe at a pitch of 4 mm. The…

A: Free stream temperature is not given in the question. Assuming free steam temperature is 25o C. To =…

Q: Q1 A diagram of a heat sink to be used in an electronic application is shown below. There are a…

A: solved

Q: A common procedure for measuring the velocity of an airstream involves the insertion of an…

Q: You are designing a small heatsink to cool a high-powered IC on a control unit PCB. The IC puts out…

Q: As more and more components are placed on a single integrated circuit (chip), the amount of heat…

A: a) Heat transfer from a fin with insulated tipq= Mtank(mL)q = hPkA θs tan h (mL)m = hPkA Cross…

Q: Problem 3 An annular aluminum (k = 240 W/m.K) fin of rectangular profile is attached to a circular…

A: An annular aluminum (k = 240 W/m.K) fin of rectangular profile is attached to a circular tube that…

Q: Two inches of urethane foam will reduce heat loss close to 1000% when applied to a 2-inch diameter…

Q: Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an…

Q: Assuming a constant flow, the equation governing the transfer of heat energy Q as a function of time…

A: Given : To find : Heat equation

Q: The thermal boundary layer in heat transfer exists whenever there is a difference between the…

A: A thermal boundary layer must form if the bulk temperature and the surface temperature differ,…

Q: Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an…

Q: Air stream at 27 degrees * C is moving at 0.3 m/s across a 100 W electric bulb at 127 degrees * C.…

A: The answer is given below

Q: 42. A fuel rod is producing heat at a rate of 8 kW/ft. The rod has a central hole. Helium flows over…

A: Given: r1=0.125 in=0.003175 mr2=0.125+18 in=0.25 in =0.00635 mr3=0.5 in=0.0127 mr4=0.5+18 in= 0.625…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If I noticed copied solution I will give dislike. In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?
In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?
Problem: Convection related Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s over a 1‐m‐long flat plate that is heated from below with a uniform heat flux of 1,250 W/m^2. Assume the flow is fully turbulent over the length of the plate. (a) Calculate the plate surface temperature, Ts(L), and the local convection coefficient, hx(L), at the trailing edge, x = L. (b) Calculate the average temperature of the plate surface, T¯s. (c) Plot the variation of the surface temperature, Ts(x), and the convection coefficient, hx(x), with distance on the same graph. Explain the key features of these distributions.
Qi/ An Aluminum flat plate has a continuous and smooth surface over which the air flows at 2 m/s. The plate consists of 25 part that each part is 10 mm long with 0.2 m width. During operation, each part is maintained at 500°C and the air is at 25°C. What is the rate of convection heat transfer from the first part? The sixth part? All the plate?
Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm outside diameter, 0.75 m long. The pipe surface temperature is 125 ° C, and the air temperature is 30 ° C. Convection coefficient = Answer W / m² ° C.
A horizontal copper plate 10 cm thick is initially uniform in temperature at 250◦C.The bottom surface of the plate is insulated. The top surface is suddenly exposed toa fluid stream at 80◦C. After 6 min the surface temperature has dropped to 150◦C.Calculate the convection heat-transfer coefficient that causes this drop.
A hot plate 1.2m wide, 0.35m high and at 1 is · Calculate the following Local heat transfer coefficient at 180 mm and average heat transfer coefficient
The outer diameter of a pipe is 25 mm and its surface temperature is 90 ° C. Air at a temperature of 30 ° C flows diagonally over the pipe at 15 m / s. What is the resistance force per unit length of the pipe? What is the heat transfer from the unit length of the pipe?
Calculate the heat flow per square meter (heat flux) through mineral wool insulation, U 5 cm thick, if the temperatures on the two surfaces are 30 and 200 °C, respectively.
5.43 A refrigeration truck is traveling at 130 km/h on a desert highway where the air temperature is . The body of the truck is idealized as a rectangular box 3 m wide, 2.1 m high, and 6 m long, at a surface temperature . Assume that (1) the heat transfer from the front and back of the truck is neglected, (2) the stream does not separate from the surface, and (3) the boundary layer is turbulent over the whole surface. Calculate the required cooling rate of the refrigeration unit.
A mercury-in-glass thermometer at 40C(OD=1cm) is inserted through a duct wall into a 3 m/s airstream at 66C. This can be modelled as a cylinder in cross-flow, as shown in the figure. Estimate the heat transfer coefficient between the air and the thermometer.