In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?

In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.10P

See similar textbooks

Related questions

Q: A horizontal tube of 125 mm diameter with an outer surface temperature of 240°C is located in a…

Q: diameter duct is maintained at a constant temperature of 245c by hot combustion gases flowing inside…

A: calculat the lenght by using the following eqation qL=hπdL(Tw-T∞)L=qhπdL(Tw-T∞) ..........(1)here ,…

Q: The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm…

Q: A thin, horizontal metal plate is maintained at a temperature of 400°C. The plate is surrounded…

Q: Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm…

A: Pipe diameter, d=100mm=0.1m Pipe length, L=0.9m Pipe surface temperature, Ts=145oC The ambient air…

Q: A spherical tank, 1 m in diameter, is maintained at a temperature of 120°C and exposed to a…

A: Heat flow is given by, In case of no insulation. k=0.017 W/m.°CFor sphere:Heat flow is given…

Q: An insulated steam pipe is used to transport high-temperature steam from one building to another.…

Q: PROBLEM 2: A horizontal cylinder of .05 m in diameter and 1 m in length maintained at a uniform…

Q: For safety reasons, air 15cmx20 cm in contact not allowed circuit board, cold air through a 20cm…

A: Given dataLength of the plate L = 20cmArea of cross section of rectangular air passage A=(…

Q: In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C…

Q: Air flows hydrodynamically and thermally fully developed at an average speed of 0.5 m/s through a…

Q: A PV cell with length 2m and width 1m was considered in an experiment to determine the PV cell…

A: for solution refer below images.

Q: A cooking pot which is cylindrical in shape with dimensions of 0.9 m in diameter and 1.2 m nigh with…

Q: Metal vapor pipe with an outer diameter of 30 mm has a surface temperature of 400 k and will be…

Q: Consider two solid copper spheres, 1 and 2. Sphere 1 has twice the diameter of sphere 2. If both…

A: Diameter of sphere 1= 2*d Diameter of sphere 2=d Initial temperature of both sphere, Ts= 0 C Air…

Q: A- A horizontal pipe 1 ft (0.3048 m) in diameter is maintained at a temperature of 250-C in a room…

A: Newton's Law of Cooling is used to determine the rate of heat transfer from the surface of the body…

Q: Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm…

A: Given: Outside diameter of the vertical pipe is 100 mm Length of the pipe is 0.9 m. Surface…

Q: It is cooled by passing air over the glass plate at 600°C. The heat transfer coefficient is 5 W/…

A: Given data: h=5 W/m2·KdTdx=-15°C/mm=-15000 °C/mk=1.4 W/m·Kε=0.8TS=600°C Need to determine the lowest…

Q: Calculate the free convection heat transfer coefficient for a plate 6 ft high and 8 ft wide at 120…

A: Given: Width of the plate is 8 ft. Height of the plate is 6 ft. Nitrogen temperature is 60 °F. Plate…

Q: The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm…

Q: To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity…

Q: Current Attempt in Progress The rear window of an automobile is defogged by passing warm air over…

Q: A long aluminum wire of diameter 3 mm is extruded at a temperature of 280°C. The wire is subjected…

A: The mean film temperature is The properties of air at mean film temperature are: The Reynolds…

Q: To ensure effective heat transfer from the food inside a freezer, the 2-mm thick layer of frost that…

Q: An electrical heater 100 mm long and 5 mm in diameter is inserted into a hole drilled normal to the…

Q: As more and more components are placed on a single integrated circuit (chip), the amount of heat…

A: a) Heat transfer from a fin with insulated tipq= Mtank(mL)q = hPkA θs tan h (mL)m = hPkA Cross…

Q: Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm…

A: Given, Outside diameter of the pipe D= 100mm Length of the pipe L= 0.75m Surface temperature of the…

Q: n overhead 25-m-long, uninsulated industrial stean ipe of 100 mm diameter is routed through a…

Q: A steel tube having k =46W/m•C has an inside diameter of 3.0 cm and a tube wall thickness of 2 mm is…

Q: Explain in your own words: (a) In what way is the heat transfer through a large steel plate that has…

A: (a) Consider a large plate that has surface its surface at specific temperature. There must be…

Q: O H.W.: The heat transfer coefficient for air flowing over a sphere is to be determined by observing…

Q: Hot water is flowing though the center of a AISI 304 stainless steel pipe with a diameter of 300mm,…

A: Given:Diameter of steel pipe, d=300 mmwall thickness, t1=10 mmLength of the pipe, L=5 mThickness of…

Q: A large bare duct having a diameter of 25cm runs horizontally across a factory area having…

A: Given data as per questiondiameter of duct =25 cmAtmosphere temperature =200c=273+20=293…

Q: The main body of plenum is a steel vessel of diameter 0.1meters has two semicircle domed ends.…

A: Given data, Diameter, D = 0.1 m Temperature of mixture inside the container, Ti = 250 °C Thickness…

Question

If I noticed copied solution I will give dislike.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

In a solar collector 1 m wide by 4 m long, the glass cover plate at an average temperature of 29°C is spaced 40 mm from the absorber plate at an average temperature of 75°C. Estimate the convection heat loss coefficient from the absorber plate to the glass when the collector is positioned horizontally. What is the convection heat loss coefficient if the spacing reduced to 10 mm?
The cartel dimensions of a vehicle are 0.6m long, 0.2m wide and 0.1m high, and the crankcase surface temperature is 350K. Calculate the heat loss flow rate from the crankcase to the atmosphere where the ambient air temperature is 276K while this vehicle is traveling at 30km/h.
Calculate the free convection heat transfer coefficient for a plate 6 ft high and 8 ft wide at 120 °F that is exposed to nitrogen at 60 °F. (see attached)
Calculate the natural convection heat transfer coefficient for a vertical stainless pipe, 100 mm outside diameter, 0.9 m long. The pipe surface temperature is 145 ° C, and the air temperature is 40 ° C. Convection coefficient = ... W / m² ° C.
A rectangular slab of butter which is 46.2 mm thick at a temperature of 277.6 K in a cooler is removed and placed in an environment at 297.1 K. The sides and bottom of the butter container can be considered to be insulated by the container sidewalls. The flat top surface of the butter is exposed to the environment. The convective coefficient is constant at 8.52 W/m2 K. Calculate the temperature in the butter at the surface, at 25.4 mm below the surface, and at 46.2 mm below the surface at the insulated bottom after 5 h exposure. k = 0.197 W/m-K, Cp = 2.30 kJ/kg-K and ρ = 998 kg/m3. Ans: T= 292.2 K , 288.3
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at T∞,i=40°C and the corresponding convection coefficient is hi=30 W/m2·K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is T∞,o= -27.5°C and the associated convection coefficient is ho=65 W/m2·K? Evaluate the properties of the glass at 300 K. a. what is Ts, i in °C? b. what is Ts, o in °C?
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at T∞,i=40°C and the corresponding convection coefficient is hi=30 W/m2·K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick window glass, if the outside ambient air temperature is T∞,o= -27.5°C and the associated convection coefficient is ho=65 W/m2·K? Evaluate the properties of the glass at 300 K. a. what is the heat flux through the original walls in W/ m^2? b. what is the heat flux through the retrofitted walls in w /m^2?
The outer diameter of a pipe is 25 mm and its surface temperature is 90 ° C. Air at a temperature of 30 ° C flows diagonally over the pipe at 15 m / s. What is the resistance force per unit length of the pipe? What is the heat transfer from the unit length of the pipe?
Write the expression for critical radius of insulation for a cylindrical pipe. Consider aninsulated pipe exposed to the atmosphere. Will the critical radius of insulation begreater on calm days or on windy days? Why?
FUNDAMENTALS OF CONVECTION Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s. What is the minimum length of the plate necessary for the Reynolds number to reach 2x107? If the critical Reynolds number is 5x105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject
Before introducing apples to cold storage, they should be cooled to a temperature of 3°C in order to avoid problems when exposing the hot apples to the much lower temperature in the storage. It is assumed that the apples are initially at 25°C, they are spheres of 7 cm diameter and that the cooling is carried out by means of an airstream at −1°C, to a such velocity that the heat convection coefficient is 30 W/(m2 °C). Calculate the necessary time to cool the apples so that its geometric center reaches 3°C. Data (apple properties): density, 930 kg/m3 ; thermal conductivity, 0.50 W/(m °C); specific heat, 3.6 kJ/(kg °C).