Q2:A. Calculate the pressure of steam at a temperature of 500°C and a density of 24 kg/m using (a) the ideal gas equation,(b) the van der Waals equation, (c) the compressibility factor, and(d) the steam table. B. What is the difference between the critical point and triple point? explain with drawing.

Q2:A. Calculate the pressure of steam at a temperature of 500°C and a density of 24 kg/m using (a) the ideal gas equation,(b) the van der Waals equation, (c) the compressibility factor, and(d) the steam table. B. What is the difference between the critical point and triple point? explain with drawing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

TOPIC: PRIOPERTIES OF SUBSTANCES: Important: Indicate units of the properties. Fill up the table provided below with your answers. Include all calculations in another sheet/s as necessary. Note: The pressure values are absolute values unless specified. Determine the properties of H2O according to the following Table: CONDITIONS: ANSWERS: 1. Saturated steam at P = 1196.8912 psia u= S= 2. Steam at T = 47 C, quality = 95 % h = 3. Steam with P = 3.53 Mpa and T = 257 C u= S =
Fig. 2. A tank contains helium at 37'C and 140 kPa gage. The helium is heated in a process by heat transfer from the surroundings such that the helium reaches a final equilibrium state at 200°C. Determine the final gage pressure of the helium. Assume atmospheric pressure is 100 kPa.
2. One cubic foot of oxygen at 100°F and 15 psia is compressed adiabatically to 0.4 ft. What then, are the temperature and pressure of the gas. If the process had been isothermal, what would the temperature and pressure have been?
3. Find the coefficient of thermal expansion a and the isothermal compressibility k from each of the following p-v-T relations: RT (a) Ideal gas equation, p = (b) Dieterici equation, p = RT e-a/RTU RT aRTV In 2b (c) Saha-Bose equation, p = In the above equations R is the gas constant and a and b are specific constants. Verify that for large values of T and v all the expressions for and K go over into the corresponding expressions for an ideal gas.
Given the pressure - volume diagram in figure below. Assume ideal gas undergo cyclic process. Path AB is adiabatic compression while path CD is adiabatic expansion. Also, paths BC and DA are isochoric processes. Ifthe value of y is 1.5, and the ratio of VilVy = 10 a. Calculate: QoalQsc b. Calculate Was assuming initial volume Vi= 2L and Pi = 1 atm. P C
1bar, v1= 10m³ to p2 =10 bar , v2 = 1m³, calculate Q3/ An ideal gas is changed from p1 Q & W for the follwing process: a- Isothermal process. b- adiabatic compression followed by cooling process at constant pressure. c- Heating at constant volume followed by cooling at constant pressure? Take Cp= (5/2)R & Cv=(3/2) R
A. Calculate the pressure of vapor at a temperature of 400°C and a density of 20 kg/m3 using (a) the ideal gas equation, (b) the van der Waals equation, (c) the compressibility factor.
Please solve it fast , Without wasting a time. (1) Is it possible to have water vapor at 5°C? If so, what would be the saturated pressure?
Explain the COMPRESSIBILITY FACTOR—A MEASURE OF DEVIATION FROM IDEAL-GAS BEHAVIOR
A cylinder contains oxygen at a pressure of 2.00 atm. The volume is 4.00 L, and the temperature is 300 K. Assume that the oxygen may be treated as an ideal gas. The oxygen is carried through the following processes: (i) Heated at constant pressure from the initial state (state 1) to state 2, which has T = 450 K. (ii) Cooled at constant volume to 250 K (state 3). (iii) Compressed at constant temperature to a volume of 4.00 L (state 4). (iv) Heated at constant volume to 300 K, which takes the system back to state 1. (a) Show these four processes in a pV-diagram, giving the numerical values of p and V in each of the four states. (b) Calculate Q and W for each of the four processes. (c) Calculate the net work done by the oxygen in the complete cycle. (d) What is the efficiency of this device as a heat engine? How does this compare to the efficiency of a Carnot-cycle engine operating between the same minimum and maximum temperatures of 250 K and 450 K?
c) ofR-134a at an initial pressure of 1.2 MPa is filled in a rigid container with a volume of 24.228 m³. The container is then cooled to 40°C. i. Determine the initial temperature and final pressure of the R-134a. Clearly show all calculations. Ikg ii. Show the process on a properly labelled pressure versus specific volume (P-v) diagram with respect to saturation lines.
If 12m3 of nitrogen at 30C and 125kPa is permitted to expand isothermally to 30m3 , (a) what is the resulting pressure ? (b) What would the pressure and temperature have been if the process had been isentropic