Calculate the reaction supports at point A and D (i.e., Ay and Dy) for the beam shown in figure, when L = 3 m, W = 6 kN/m. B. 2 m 4 m Select one: a. Ay = 13 kN and Dy = 5 kN b. Ay = 11 kN and Dy = 7 kN c. Ay = 12 kN and Dy = 6 kN d. Ay = 6 kN and Dy = 12 kN

Calculate the reaction supports at point A and D (i.e., Ay and Dy) for the beam shown in figure, when L = 3 m, W = 6 kN/m. B. 2 m 4 m Select one: a. Ay = 13 kN and Dy = 5 kN b. Ay = 11 kN and Dy = 7 kN c. Ay = 12 kN and Dy = 6 kN d. Ay = 6 kN and Dy = 12 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

plzzzz help me nowww What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
The gate AB shown in figure is hinged at A and kept closed by a force P at B. Compute for the Hydrostatic Force acting on the side of the gate AB. (Given: p = -18.46 kPa, OIL SG = 0.8)
A 10m diameter storage tank, 15m high is used to contain four different liquids. 2.50m of liquid A(SG=085), 5m of liquid B(SG=2.40), 3.80m of fresh water, and 2.70m of liquid CSG=7.79). It is provide with two steel bands installed 1m from the top and 1m from the bottom. Determine the : a) total hydrostatic force acting on the wall of the tank. b) the line of action of the total force from the bottom c) tensile force at the top band and the tensile force at the bottom band. Please draw the complete pressure diagram with proper labelling.
Flow In Closed Conduits 5. Water at 65F is pumped to a tank through a 750 ft 12-in diameter galvanized iron pipe and the flow is 4.5 cfs. (a) Determine the head lost due to friction. (b) How much power, in HP, is required to overcome this head loss? Answers: (a) _______________________________ (b) _______________________________
the system consists of 1000m of 50mm cast iron pipe, two 45° and 4 90° flanged long radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. Water flows at rate of 4.5 L/s from pt. 1 to the reservoir whose free surface lies 100m above pt.1. Kinematic viscosity is 1.02x10^-6 sqm/s and f=0.035. compute for: a.) reynolds number b.) total head lossv(m) c.) gage pressure at 1 to deliver water into the reservoir (kPa)
A copper tube 80 mm diameter and 2.5 mm thick is plugged at its ends and filled with water without applying any external pressure . It is observed that when an axial push is applied at ends , the water pressure rises to 0.12 N / mm² . Find value of axial push . Take Ecu = 102 GPa , Kwater = 2.2 GPa and μ = 0.32 .
Note: Where appropriate, assume that Young's modulus (E) for steel is 200 KN mm-2 and the coefficient of thermal expansion of steel (a) is 0.0000112 per °C. OWN SOLVING AND NOT CHATGPT FOR UPVOTE SKIP IF YOU ALREADY DID THIS OR ELSE DOWNVOTE
A closeted tank kept partially filled with oil (sp.gr. = 0.9) has a pressure in the gas space above the oil of 10 psig. If the oil is discharging through a hose at 50 gpm, estimate the pressure at the nozzle located 10 ft lower than the oil surface and with a 1” i.d. discharge. Assume the total friction loss in the line amounts to 1.0 ft-lbf/lbm.
A simple beam AB supports two concentratedloads P at the positions shown in the figure. A support C at the midpoint of the beam is positioned at dis-tance d below the beam before the loads are applied. Assuming that d 5 10 mm, L 5 6 m, E 5 200 GPa, and 198 10 mm 6 4 I 5 3 , calculate the magni-tude of the loads P so that the beam just touches the support at C.
A.) The loss factor for a 90 degree elbow is: B.) The total form friction head loss in ft is C.) The actual shaft work needed (since pump efficiency is only 60%) in horsepower or hp is: A centrifugal pump takes brine from the bottom of a supply tank and delivers it into the bottom of another tank. The brine level in the discharge tank is 150 ft above that in the supply tank. The line between the tanks is 600 ft of 4-in. Schedule 40 pipe. The flow rate is 400 gal/min. In the line are two gate valves, four standard tees, and four ells. What is the energy cost for running this pump for one 24-h day? The specific gravity of brine is 1.18, the viscosity of brine is 1.2 cP, and the energy cost is $400 per horsepower-year on a basis of 300 d/yr. The overall efficiency of pump and motor is 60 percent.
Design an I section purlin for an industrial building with Galvanized iron sheets as the roofing material. Span of the truss =14m; Spacing of trusses = 7m c/c; Spacing of purlins = 1.3m c/c; Wind pressure intensity = 3 kN/m2 weight of GI sheets =140N/m2 ; Grade of steel: Fe 410.
Calculate the pressure at point A in the manoter shown. beight b'c = 0.50m