Calculate the resistance of 100 m length of a wire having a uniform cross-sectional area of 0.1mm² if the wire is made of manganin having a resistivity of 50 x 10- Q-m. If the wire is drawn outto three times its original length, by how many times would you expect its resistance to beincreased?[500 22; 9 times]

Answered: Image /qna-images/answer/907a90f3-48bc-40c1-b002-e3df65adb24d.jpg

Calculate the resistance of 100 m length of a wire having a uniform cross-sectional area of 0.1 mm² if the wire is made of manganin having a resistivity of 50 x 10-8 Q-m. If the wire is drawn out to three times its original length, by how many times would you expect its resistance to be increased? [500 0; 9 times]

Calculate the resistance of 100 m length of a wire having a uniform cross-sectional area of 0.1 mm² if the wire is made of manganin having a resistivity of 50 x 10-8 Q-m. If the wire is drawn out to three times its original length, by how many times would you expect its resistance to be increased? [500 0; 9 times]

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter6: Ground-fault Circuit Interrupters, Arc-fault Circuit Interrupters, Surge Protective Devices, Immersion Detection Circuit Interrupters, And Appliance Leakage Current Interrupters

Section: Chapter Questions

Problem 26R

See similar textbooks

Similar questions

a. Determine the ampacity of four heat resistant conductors up to 90 C of #10 gauge copper installed in a rigid tube at 30 C ambient temperature. b. What is the ampacity of a 500 KCMIL THHN insulated aluminum conductor at an ambient temperature of 60 C?
A silver wire has a resistance of 2.5 ohms. What will be the resistance of amanganin wire having a diameter, half of the silver and length one third? Thespecific resistance of manganin is 30 times that of silver.
a silver wire has a resistance of 3.5 ohm. what will be the resistance of manganin wire having diameter, half of the silver wire and length one-fourth? The specific resistance of manganin wire is 25 times that of silver
An AWG #10 copper wire conductor has an 80.8 mil diameter. A 50-foot length carries a current of 30 Amperes. Find the electric field intensity E within the wire, the voltage drop across the conductor, and the resistance R of the 100-foot length.
Determine the resistance of a copper tube 0.5 cm and 2 m long. The external diameter and resistivity are 10 cm and 9.071349x10-2 Ω-m respectively. A coil of annealed copper wire whose resistivity is 10.37Ω-CM/ft has 820 turns, the average length of which is 9 inches. If the diameter of the wire is 32 mils, calculate the total resistance of the coils at 20o C
A copper wire 100 m long must experience avoltage drop of less than 1.5 V when a current of 2.5 A passesthrough it. Given that copper has an electrical conductivity of6.0E7 /(Ὠ-m), compute the minimum diameter of the wire.
An annealed copper wire, 2-km long, is being used as conductor in an electrical system in an environment temperature of 38°C. If the diameter of the wire is 0.65 cm, determine its total resistance.
11. What is the resistance of 600 ft. of no. 20 copper wire? Given : Area =1022 circular mils and resistivity ( P) of 10.4 cm- ohms / ft.
Find the resistance of a silver wire 80-yard-long and 0.0045 inch in diameter (T = 20°C).
A cylindrical copper rod having a diameter of 0.40 in has a resistance of 0.00264 Ω. Taking the resistivity of copper as 1.745 µΩ-cm at 20o C, determine the length of the rod in ft. resistance of the rod when it is drawn down to one-third of the initial diameter, the volume remaining unchanged. Assumed that the resistivity of the copper is not affected by the drawing process.
The wires of our appliances are insulated with a material mixed with rubber, which has a very high resistivity. If a certain wire has a length of 2.5 m and the outer diameter is 5mm and its inner diameter is 0.5mm, what is its resistance? Note that the inner diameter is present to leave a hallow place where conducting wire ( usually copper) is present. Follow the format: Given: Required: Equation: Solution: Answer:
Neglecting losses and fringing effects and assuming the substrate of a stripline to have a thickness of 0.42 (mm) and a dielectric constant of 2.83, determine the required width (in mm) of the metal strip in order for the stripline to have characteristics resistance of 78 Ohms. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.