High-PturbineLow-PturbineReheaterBoilerP=Ps=PaeheatPumpCondenserThe following data was given for a steampower plant operating on the ideal reheatRankine cycle.3-4: Inlet steam at 17.5 MPa and 600Click Save and Submit to save and submit. Click Save All Answers to saveall answers.3-4: Inlet steam at 17.5 MPa and 600°C6-1: inlet steam at a pressure of11.16 kPa at a wetness fraction of0.1.At state 1, the specific volume is0.00101 m³/kgCalculate the specific heat input ofthe system in kJ/kg to 3 decimalplaces.7L

Given: Ideal reheat Rankine cycle Process 3-4: Inlet steam at 17.5 MPa and 6000C 6-1: Inlet steam at…

Answered: Calculate the specific heat input of…

Engineering

Mechanical Engineering

Calculate the specific heat input of the system in kJ/kg to 3 decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an ideal Reheat cycle , the steam throttled condition is 7 Mpa and 460 C. The steam is then reheated to 1.5 MpA and 460 C . If turbine exhaust is 50 C ,determine the following: A.) Quality after turbine expansion B.) Turbine work C.) Heat added in the boiler D.) Heat rejected from the condenser E.) Pump work F.) Net work G.) Cycle efficiency
A steam power plant operates on an ideal Rankine cycle with two stages of reheat and has a net power output of 75 MW. Steam enters all three stages of the turbine at 550C. The maximum pressure in the cycle is 10 MPa, and the minimum pressure is 30 kPa. Steam is reheated at 4 MPa the first time and at 2 MPa the second time. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the thermal efficiency of the cycle, and (b) the mass flow rate of the steam.
A gas-turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1600 kPa. The working fluid is air, which enters the compressor at 40C at a rate of 850 m3/min and leaves the turbine at 650C. Using variable specific heats for air and assuming a compressor isentropic efficiency of 85 percent and a turbine isentropic efficiency of 88 percent, determine (a) the net power output, (b) the back work ratio, and (c) the thermal efficiency.
Show the COMPLETE SOLUTIONS and DIAGRAM (pv and Ts) including the switching of table and interpolations/extrapolations: NO Calculator Technique and Applications. A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of 3 MPa and 50 kPa. The temperature of the steam at the turbine inlet is 300°C, and the mass flow rate of steam through the cycle is 35 kg/s. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the thermal efficiency of the cycle and (b) the net power output of the power plant.
15. The actual Rankine cycle has an 90.22% turbine isentropic efficiency and 81.14% pump isentropic efficiency. If in the ideal Rankine cycle, the heat input in the boiler - 903 kW, the turbine work output 394 kW, and pump work input = 17 kW, what is the actual cycle thermal efficiency if the heat input in the boiler is the same for the actual cycle? Express your answer in percent.
1. Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of45 MW. Steam enters the turbine at 7 MPa and 500°C and iscooled in the condenser at a pressure of 10 kPa by runningcooling water from a lake through the tubes of the condenserat a rate of 2000 kg/s. Show the cycle on a T-s diagram withrespect to saturation lines, and determine (a) the thermal efficiency of the cycle, (b) the mass flow rate of the steam, and(c) the temperature rise of the cooling water. Answers:(a) 38.9 percent, (b) 36 kg/s, (c) 8.4°C 2. Consider a 210-MW steam power plant that operateson a simple ideal Rankine cycle. Steam enters the turbine at10 MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa. Show the cycle on a T-s diagram with respectto saturation lines, and determine (a) the quality of the steamat the turbine exit, (b) the thermal efficiency of the cycle,and (c) the mass flow rate of the steam. Answers: (a) 0.793,(b) 40.2 percent, (c) 165…
A simple rankine ideal cycle with water as the working fluid. Twenty kilograms of steam enters the turbine at 7.356 MPa and 500.356 oC and is cooled in the condenser at a pressure of 10.356 KPa by running cooling water from a lake through the tubes of the condenser at rate of 2000 kg. Show the T-s diagram and schematic of simple rankine cycle. For cycle determin (a) the turbine work, (b) the heat added, (c) the temperature rise of the cooling water, (d) the thermal efficiency of the cycle. For engine, determine (e) the heat added, (f) the thermal efficiency of the engine, and (g) Draw the T-s and schematic diagram.
What is the main effect of superheating the cycle, discuss the need for superheated steam in a power generating plant?
The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 ˚C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Calculate the specific heat input of the system in kJ/kg to 3 decimal places.
The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 ˚C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the dryness fraction of steam at state 6 to 1 decimal places.
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of 1250 and 2 psia. The mass flow rate of steam through the cycle is 75 lbm/s. The moisture content of the steam at the turbine exit is not to exceed 10 percent. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the minimum turbine inlet temperature, (b) the rate of heat input in the boiler, and (c) the thermal efficiency of the Cycle. Answers:
IDEAL RANKINE CYCLE: In an ideal Rankine Cycle, steam at 5 MPaa and 500 o C enters the turbine and expands 300 KPaa. For 110,000 kg/hr of steam, find: a) Ideal power output of the Turbine (kW), b) Power to drive the pump (kW), c) Rate of Heat Added (kW), d) thermal efficiency of cycle and engine, e) steam rate of the cycle and engine, f) Heat Rate (PLEASE SHOW COMPLETE SOLUTION AND ENCLOSE ALL THE FINAL ANSWERS ROUNDED OFF TO THE 4TH DECIMAL)