Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE NSCP 2015. A plate with width of 500 millimeters and thickness of 25 millimeters is to beconnected to a double plate of the same width and with a thickness of 10 mmeach by a 36-millimeter-diameter bolts, as shown in the figure. The plates are allA36 steel with a yield strength of 250 MPa and an untimate tensile strength of400 MPa. It is required to determine the value of "b" such that the net widthalong the bolts 1-2-3-4 is equal to the net width along bolts 1-2-4.60 mm100 mm100 mmP500 mm100 mm.PA150 mm 13

Answered: Image /qna-images/answer/649ddc71-dd09-499d-8d7d-66a157865f84.jpg

Answered: Calculate the value of P so that the…

Engineering

Civil Engineering

Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE NSCP 2015.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a plate having a width of 400 mm and thickness of 12 mm is to be connected to another plate by 34 mm diameter bolts as shown in the figure. Assume diameter of holes to be 2 mm larger than the diameter of the bolts. Use A 36 steel plate with yield strength Fy = 248 MPa and minimum tensile strength Fu = 400 MPa. For a chain holes extending across a part in any diagonal or zigzag line, the net width of the part shall be obtained by deducting from the gross width the sum of the diameters or slot dimensions of all holes in the chain and adding, for each gage space in the chain, the quantity S24g where S is the longitudinal center to center (pitch) of any consecutive holes, in millimetres and g is the transverse center to center spacing (gage) between fastener gage lines in millimetres. If a = 60 mm, c = 150 mm and d = 100 mm. Determine the nearest value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Determine the nearest value…
Shown in Figure 1 is a centrically loaded bolted connection. The diameter of the bolts is 19 mm while holes have 21 mm diameter. Use depth 4y = 200 mm. 1. Determine the critical net width (Net Width) for the staggered bolted connection as shown in the figure. 2. Determine the value of "x" so that the net width along bolts A-B-C-D-E is equal to the net width along bolts A-B-D-E.
The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N type) on each side. Based on the shear strength of bolts only, the maximum Pu that can be applied to the splice is equal to: Group of answer choices 202 kips 322 kips 161 kips 405 kips
For two lines of M20 bolts shown in the figure, determine the pitch (s) in mm that will give it a net area DEFG equal to the one along ABC and determine the tensile strength (kN) of the plate if it is 12 mm thick Use the pitch (s) that gives it a net area DEFG equal to the one along ABC
A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate is A36 steel. Assume allowable tensile stress on net area is .60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths
A plate 400x12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter bolts, as shown. The holes are 2 mm larger than the bolt diameter. The plate is A36 steel. Assume allowable tensile stress on net area is .60Fy. It is requireed to determine the value of b such that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4
The lap connection shown in Figure 3 shows nine 20 mm - diameter A325 bolts spaced as follows: S1 = 50 mm S3 = 50 mm S2 = 80 mm S4= 100 mm Thickness of plates, t= 25 mm Bolt hole diameter = 23 mm Tensile strength and stresses: Yield strength, Fy = 248 MPa Tensile strength of steel, Fu = 400 MPa Allowable tensile stress on gross area = 0.6Fy Allowable tensile stress on net area = 0.5Fu Allowable bolt shear stress= 120 MPa Allowable bolt bearing strength = 480 MPa Calculate the allowable tensile load (kN) based on the following conditions: Based on bearing strength of bolt. 2160 2387 2475 4320Based on shearing strength of bolts. 339 368 415 524Based on tensile strength of plate. 958 1116 1155 1325
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate with four 5 ⁄8-inch-diameter bolts as shown in Figure 1. Assume that the effective net area Ae equals the actual net area An. (a) Calculate the design strength for LRFD? (b) Calculate the allowable strength for ASD?
A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572 Grade 50 plate material has a width of 150 mm and thickness of 16 mm. Assume diameter hole to be 24 mm. Bolt threads are excluded from the shear plane. Allowable stress of A 325 bolts: Fv = 207 MPa Fp = 1.5 Fu (to prevent excessive hole deformation) Allowable stresses of A572 Grade 50 plate material: Fy = 345 MPa Fu = 450 MPa a. Compute the tensile capacity due to the failure of the plates. b. Compute the tensile capacity due to the failure of the bolts.
4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
A staggered riveted connection has rivets arranged as shown below. The plate is 400 mm and 12 mm thick with four bolt holes. The diameter of rivet is 34 mm The diameter of the rivet hole is assumed to be 5 mm larger than rivet diameter. Fy = 248 MPa. Fu= 410 MPa, Fv in rivets is 372 MPa. 1. Which of the following gives the distance b so that the net area in section 1 – 2 – 3 – 4 equal to the net area in section 1 – 2 – 4 a. 30.01 mm b. 25.12 mm c. 19.7 mm d. 12.23 mm 2. Which of the following gives the net area using the computed value of b. a. 4622.65 mm² b. 5623.75 mm² c. 3623.64 mm² d. 7652.85 mm² 3. Which of the following gives the maximum tensile force that the connection could carry if the allowable yield stress is Fy/1.67. a. 432.12 kN b. 724.73 kN c. 253.25 kN d. 712.81 kN 4. Which of the following gives the maximum tensile force that the…