A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate with four 5 ⁄8-inch-diameter bolts as shown in Figure 1. Assume that the effective net area Ae equals the actual net area An. (a) Calculate the design strength for LRFD? (b) Calculate the allowable strength for ASD?

A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate with four 5 ⁄8-inch-diameter bolts as shown in Figure 1. Assume that the effective net area Ae equals the actual net area An. (a) Calculate the design strength for LRFD? (b) Calculate the allowable strength for ASD?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

Plate connection with bolts with shear strength value T=200 MPA is given in the figure. Determine the minimum required bolt diameter for the safe transfer of the P=70 kN load.
The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: a. nominal tensile strength (kN) based on gross yielding.
5. a bolted lap joint shown in the figure below. The bolts are 20m in diameter in 23 mm holes. The plates are 12m thick X350 Allowable stress of Plates: Tenaion in gross area0.60Fy Tension in net area0.50 Fu Shear on Net Area 0.30Fu Yield Strength of plate, Fy 248 Npa Ultinate tensile strength of Plate. Fu400 Mpa x, Find the safe load P based on a- Gross area yielding b. net area rapture c. block shear 2 of 3
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
: Verify, using appropriate Chapter E design provisions, the tabularized (Table 4-7) buckling capacity of a WT6X20 for both the x- and y-axes at (KL)x = (KL)y = (KL)z = 10 ft. Assume A992 steel.
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area.
The shape shown in Figure is a W18 x71 with holes in each flange for 1-inch-diameter bolts. The steel is A992. Compute the nominal flexural strength for an unbraced length of 10 feet. Use Cb =1.0.
Three steel bolts are to be used to attach thesteel plate shown to a wooden beam. Theplate will support a 110kN and the ultimateshearing stress for the steel used is 360MPaand that a factor of safety of 3.35 is desired,determine the increase in the bolt diameterrequired if an additional 100kN load is addedto the existing 110kN.
Calculate the strength of a 75 × 50 × 6 mm when used as a tension member with its longer leg connected byI. 16 mm diameter rivetsII. Fillet weld
If use single-angle (L5x3x3/8) tensile member connected by two line of bolts 7/8in at last three bolts in a line 4in, from table D3-1 case 2 the value of U equal to
The tension member shown in Figure is an L6 × 3 ½× 5/16. The bolts are ¾ inch ameter. If A36 steel is used, is the member adequate for a total load of 100 kips?