Calculate the voltage gain of the following circuit. Assume that the capacitors are very large and A = 0. Şekilde gösterilen devrenin gerilim kazancını hesaplayınız. Kapasitelerin çok büyük olduğunu ve A = 0 kabul ediniz. Circuit parameters / Devre Parametreleri Rsig = 8 kQ, RG = 27 kQ, Rs = 300 N, RL = 5 kN, gm = 0,05 S VDD RG R sig M1 C2 oVout sig Rs RL O a. 0.76

Calculate the voltage gain of the following circuit. Assume that the capacitors are very large and A = 0. Şekilde gösterilen devrenin gerilim kazancını hesaplayınız. Kapasitelerin çok büyük olduğunu ve A = 0 kabul ediniz. Circuit parameters / Devre Parametreleri Rsig = 8 kQ, RG = 27 kQ, Rs = 300 N, RL = 5 kN, gm = 0,05 S VDD RG R sig M1 C2 oVout sig Rs RL O a. 0.76

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 34RQ: Which of the following is the capacitance of an 88-microfarad and a 108-microfarad starting...

See similar textbooks

Similar questions

If a capacitor produces 15 ampere on a 240-volt supply, which of the following is its microfarad rating? 166 microfarad 15 microfarad 200 microfarad 3450 microfarad
The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the power factor is 62.5%. The resistor has a voltage drop of 14.993 V, the inductor has an inductive reactance of 60 , and the capacitor has a capacitive reactance of 45 . ETITZVA29.985PF62.5%ER14.993VIRRPELILXL60VARsLLECICXC45VARsCC
Various parameters of Schering bridge are given as follows. The voltage supply of 2 kHz is connected to terminals A and C and detector to points B and D. Arm AB comprises the unknown Resistor R1 and capacitor C1. Arm BC consists of resistor R2 of 18k 2. Arm DA consists of capacitor C2 of 0.06 µf. Arm CD has R3 of 1.5k2 and C3 of 2nf are in parallel. Calculate (i) the capacitance (C1) (ii) the equivalent series resistance (R1) and (iii) dissipation factor. Also draw the schematic diagram.
CAPACITOR VOLTAGE v( t) in circuit ( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Solve no.11 and show solutions. (Situation no.05 image below)
a capacitor C is connected in parallel to a resistor R across a 100V, 100Hz supply. The supply current is 10A at a phase angle of 64.45 degree. Determine the value of R and C. A. 25.52 ohm, 130.51 microfarad B. 5 ohm, 10microfarad C. 1kohm, 2 F D. 10 ohm, 25 micro Farad
Q27/B Draw the schematic diagram of Anderson's bridge circuit. Write the formula for unknown resistance, self inductance and quality factor.
The following three impedances are connected in series across a 40 V, 20 kHz supply: (i) a resistance of 8W, (ii) a coil of inductance 130 µH and 5 W resistance, and (iii) a 10W resistor in series with a 0.25 µF capacitor. Calculate the circuit current, the circuit phase angle and the voltage drop across each impedance. A capacitor C is connected in parallel with a resistor R across a 120 V, 200 Hz supply. The supply current is 2 A at a power factor of 0.6 leading. Determine the values of C and R. A coil of 300 turns is wound uniformly on a ring of non-magnetic material. The ring has a mean circumference of 40 cm and a uniform cross sectional area of 4 cm2. If the current in the coil is 5 A, calculate the magnetic field strength, the flux density and the total magnetic flux in the ring.
HELPP Since the oscilloscope image of the circuit given in Figure 1 is as in Figure 2, find the value of the capacitor C1.
Thyristors are ideal in the circuit in Figure 2. The internal resistances of the sources are neglected, but each has Lk=6 mH ,series leakage inductance is taken into account. At 50Hz, Vˆ= 250V , with an ignition angle of α = 90º and full voltage Id= 8A It is studied with filtered current ( Ly=oo ). a) Find the transmission angle (ü) and transmission time. b) Find the average voltage on the load without neglecting the transfer. The formulas for this circuit and this study are in Annex-1: c)Draw the y v waveform, showing the transmission notches.
A three parallel plate capacitor sensor is used to measure the linear displacement. The capacitor sensor has an area of 400mm 500 mm, and 8mm distance between all three plates. If the lower plate is moved up by 2mm with middle and upper plates kept fixed. Calculate, i. The distance between the middle plate to upper plate and middle plate to lower plate. ii. Net capacitance of the capacitor sensor.
10. The higher the frequency, the easier it becomes to analyze electronics circuits.a. Not all the timeb. Truec. Falsed. In some cases only11. The __ ___ leads ensure low inductance and permit high currents.a. Short, fatb. Long, fatc. Long, thind. Short, thin12. Most microwave amplifiers have input and output impedances of _a. 75Ωb. 50Ωc. 300Ωd. 120Ω Note: Explanation is not needed just provide the correct answers for each number.