Answered: California Electrical Transmission…

California Electrical Transmission Company has to supply the demand of four companies in different hours. Calculate following: (i) Diversity Factor (ii) Units generated/Day (iii) Load Factor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter10: System Protection

Section: Chapter Questions

Problem 10.1P

See similar textbooks

Related questions

Q: Sketch, using single line diagram, a typical transmission and distribution system with the…

A: We have given sketch using single line diagram a typical transmission and distribution system with…

Q: If Voltage regulation of Transmission line increases Efficiency will decreases Select one: True…

A: Choose the correct option If the voltage regulation of transmission line increase, efficiency will…

Q: ) In terms of load assessment, define the following: Demand Factor Load Factor Diversity

A: As per Bartleby guidelines we are allowed to solve only one question with maximum three subparts,…

Q: Three-bus system network consists of TWO generators located at buses 1 and 2 and TWO loads located…

A: The Given is V1=j0.5∠0° and V2=1.03, PG2=2pu SD2=0.5+j0.2 and SD3=0.6-j0.25 The Given Matrix is…

Q: 4.14 The incremental fuel costs for two generating units G, and G, are given by IC, = 25 + 0.2 PG,…

A: we need to determine PG1 and PG2.

Q: 50 km of single-phase transmission line, 800 kVA power 8 kV, is carried with 0.9 reverse power…

A: The given information in the above problem are 1. Length of the line = 50km 2. Power carried by the…

Q: pen PowerWorld Simulator case Example 5_10 with the series capacitive compensation at both ends of…

A: P=VI cos∅To determine maximum amount of real power that can be transferred to the load at unity…

Q: For the power system network shown

A: The above diagram represents a 3 bus power system network. Bus1 is a slack bus Bus 2 is load bus Bus…

Q: For each of the following power systems, do following: 1. Compute the Y_bus in rectangular and polar…

A: We are authorized to answer three subparts at a time. Since you have not mentioned which part you…

Q: Write the Installed Generation Capacity of Sultanate of Oman with current energy share of…

A: Write the installed generation capacity of sultanate of oman with current energy share of…

Q: Q1/ Explain in detail VOLTAGE DROP / RISE IN TRANSMISSION LINE With mathematical examples

Q: f) Write the Installed Generation Capacity of Sultanate of Oman with current energy share of…

Q: The voltage regulation of a transmission line is negative for lagging power factor. Select one: O…

A: Given Voltage regulator is negative for lagging load True or false

Q: The value of value of voltage measured in residential convenience outlet is average voltage. True…

A: Average value is the average of the signal over the period of time. Where as rms value of the signal…

Q: A)Ibc =? find the load current=?…

A: A)Ibc =? find the load current=? B)Vca calculate the line voltage =? C)Calculate the total complex…

Q: What will be the power loss of a distribution line if the power at the sending and receiving end is…

A: In this question we need to find the power loss in transmission line and efficiency of line

Q: For a transmission line, if the terminal is short-ended, is the input impedance will be zero? If…

A: for a transmission line : if the terminal is short ended is the input impedance will be zero if not…

Q: A generating plant containing three identical 40 MW generating units is connected to a constant 82…

A: SI No Unit Failure rate Repair time Frequency Duration Failure probability 1 40 MW 3…

Q: The required change in generation, called the area control error or ACE, represents the shift in the…

A: Choose the given statement is correct or false. The given statement The required change in…

Q: For a given power transfer, a star system is associated with larger line currents. Select one: True…

A: In this question, we have to tell about for given power transfer , a star system is associated with…

Q: A three-phase transmission line is feeding from a 400-MVA, 240/24 kV transformer at its sending end.…

Q: The span between two level supports for a 132 KV overhead transmission line is 200 The weight of…

A: According to question: Total weight of 1m length of conductor is calculated as…

Q: Derive the ABCD constants for two transmission lines connected in parallel.

Q: a) Find the IBC load current. b) Give the Vca line voltage

A: Find the IBC load current. b) Give the Vca line voltage.

Q: Current through the line Sending end voltage Sending end power factor Regulation of transmission…

Q: Determine the per unit impedance of a transmission line having an impedance of 30 + j110 Ω on 100…

Q: In single phase AC distribution system, the distance of separation between wires is relatively…

A: Single phase AC DISTRIBUTION SYSTEM WIRE DISTANCE SMALLER COMPARE TO OVERHEAD LINE TRUE

Q: A private developer proposes to install a synchronous type generating plant connected to the local…

A: Answer(1) According to the given data The generator produces 14 MW at 11 kV So, during the peak…

Q: Explain load flow analysis in power system using optimization algorithm with neat diagram.

A: Load flow analysis in power system: It is a procedure of determining steady-state operating…

Q: calculate power flow for IEEE 30 bus manually using NR method Please hand written solution

Q: Several natural processes can interfere with the proper functioning of a transmission line, such as…

A: It is given that several natural processes can interfere with the proper functioning of a…

Q: jo.os (り (1) (3) jro (5) 3 jo.s pafference

Q: Find the IBC load current b) Give the VCA line voltage c) Calculate the total complex power on the…

A: Find the IBC load current? Give the VCA line voltage? Calculate the total complex power on the…

Q: For a single phase ac voltage controller/chopper, which is designed by using thyristors, with the…

Q: Enlist the power quality issues for renewable energy integration

A: Renewable energy is also called green energy because it is generated from Energy resources which are…

Q: Florida Electrical Transmission Company has to supply the demand of four companies in different…

A: The solution can be achieved as follows.

Q: If for example communication power is often normalized by assuming R to be a unity in Ohms, although…

A: Power is usually referred to as the amount of energy transfer from one form to another and…

Q: 014: Fill in the blanks with suitable answers: 1. One of the advantages of an interconnected power…

A: 1). One of the main advantage of interconnected power system is power shared incase of exceeding the…

Q: Draw the load curve and find () maximum demand, (i) units generated per day, (ii) average load, (iv)…

Q: A 400 km long, 50 Hz transmission line having series resistance and inductance of 0.12/km and…

A: Given: A 400 km long, 50 Hz transmission line have Resistance, R=0.1 Ω/km Inductance, L=1 mH/km…

Q: In single phase AC distribution system, the net drop is the difference of the drop in resistance due…

A: In a single phase system, the net Voltage drop is equal to product of phasor current flows through…

Q: For a single phase ac voltage controller/chopper, which is designed by using thyristors, with the…

A: A rectifier circuit is used to rectify the AC power generated by this source to the DC power that…

Q: se the method of nodal analysis to find the branch currents indicated in the networks of

Q: Calculate the per unit voltage drop on the transmission line e) Calculate also the sending end…

Q: the distribution of loads among the generating units is called as economic dispatch. Select one:…

A: Economic load dispatch in the power system is very important in optimizing loads among the…

Q: what is the power loss in the line in megawatt (MW)?

Q: (1) In terms of load assessment, define the following: Demand Factor Load Factor Diversity

A: As per the guidelines of Bartley we supposed to answer first question only since both question are…

Q: Q1: Perform load line analysis for the following circuit using the figure given below. Where E=20V.…

A: consider the given question;

Q: At low power factor, the feeders have to carry more current for the same power to be transmitted.…

A: We know that active power is VIcosphi . As cosphi is very low, it has to draw more current to…

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

California Electrical Transmission Company has to supply the demand of four
companies in different hours.
Calculate following:
(i) Diversity Factor
(ii) Units generated/Day
(iii) Load Factor.
Company/time
8АM-6PM
бАМ-10AM
10АM -6РМ бРМ-6АM
KMD limited
250 KW
COLOPO
150 KW
VELKA
100 KW
BNLF
150 KW
150 KW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The units of admittance, conductance, and susceptance are siemens. (a) True (b) False
Two three-phase generators supply a three-phase load through separate three-phase lines. The load absorbs 30 kW at 0.8 power factor lagging. The line impedance is (1.4+j1.6) per phase between generator G1 and the load, and (0.8+j1) per phase between generator G2 and the load. If generator G1 supplies 15 kW at 0.8 poir factor lagging, with a terminal voltage of 460 V line-to-line, determine (a) the voltage at the load terminals. (b) the voltage at the terminals of generator G2, and (c) the real and reactive power supplied by generator G2. Assume balanced operation.
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
a single phase 11 KV line with the length of 15 kilometre is to transmit 500kva the inductive reactance of the line is 0.5 ohm per kilometre and resistance is 4.3 ohm per kilometre calculate the efficiency and regulation of 40.8 lagging power factor
A single phase transmission line is delivering 410 kVA load at 10 kV. Its resistance is 5.5 ohm and inductive reactance is 8 ohm if the load power factor is 0.7 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line
Company Y would like to have a new installation transmission line to open a small new city consist of 300 MW with 0.85 power factor lagging at full load. The new transmission line required 132 kV with 124.274 miles long. All the elements needed for the new transmission line is listed in table shown in the picture. You are required to model the transmission line and analysed the performance of the new transmission lines in terms of voltage regulation and efficiency. Note that the frequency used is 50 Hz.
The yearly load duration curve of a certain power station can be approximated as a straight line ; the maximum and minimum loads being 80 MW and 40 MW respectively. To meet this load, three turbine generator units, two rated at 20 MW each and one at 10 MW are installed. Determine (i) installed capacity (ii) plant factor (iii) kWh output per year (iv) load factor.
A three-phase transmission line receiving end voltage is rated at 21 kV. A load of 1500 KW is connected at the receiving end of the transmission line 70 km long. The parameters of the transmission line are given by r = 0.09 Ω/km and x = 0.8 Ω/km. If the machine is working at 0.65 power factor lagging. Determine a) The series reactance of the transmission line b) Sending end line voltage c) Percentage Voltage regulation d) Percentage Efficiency
A single phase transmission line is delivering 490 kVA load at 14 kV. Its resistance is 6 Ω and inductive reactance is 7 Ω if the load power factor is 0.7 lagging. Determine the: A) Current through the line. B) Sending end voltage. C) Sending end power factor. D) Regulation of transmission line. E) Efficiency of transmission line.
Estimate the distance over which a load of 15000 kW at 0·85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminum each of resistance 0·905 Ω/phase per kilometer. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7·5% of the load.
single phase overhead transmission line delivers 4000 KW at 11KV 8.8 power factor lion if resistance and reactance for conductor are 0.15 women 0.02 ohm respectively calculate percentage regulation sending and power factor line losses
Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase transmission line, 60HZ, have: (50 MW, 0.866 lagging p.f. and 132 kv in receiving end. If the line have (Z = 100 <80 Ohm / phase and Y = 0.0012 <90 S). Calculate: Vs, Is, Vreg, and power factor in sending end. Also, find the transmission efficiency? For the following transmission models: 1- Short transmission line model. 2- Medium transmission line (pi) model. 3- Medium transmission line (T) model. 4- Long transmission line model. (Please show your answer steps)