Canoes have been created out of concrete, believe it or not (and they actually float). Despite the fact that concrete has a lower density than aluminum, a concrete canoe of the same size weighs much more. What is the reason behind this? (If the length and breadth of two canoes are the same, they are the same size.)

Canoes have been created out of concrete, believe it or not (and they actually float). Despite the fact that concrete has a lower density than aluminum, a concrete canoe of the same size weighs much more. What is the reason behind this? (If the length and breadth of two canoes are the same, they are the same size.)

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.33P: According to Figure 5-20, is ii possible to completely separate one of the four materials from the...

See similar textbooks

Similar questions

Help me with Solution, Need fast. Do not waste time. A steel beam is installed in a building when the ambient temperature is -12C. If the beam if fixed at it's ends (prevented from expanding/contracting), calculate the stress that will develop in the beam if the ambient temperature rises to +32C. State whether the stress is tension or compression. Assume E 200,000 MPa and \alpha L = 12x10-6 (/\deg C)
Can you show to solve the Mn= 424.063 kn.m How it gets the answer the 424.063 , the green highlights below Please show solution Civil engineering- steel design
The assembly consists of a 20-in. wooden dowel rod and a tight-fitting steel collar. Determine the distance x̄ to its center of gravity if the specific weights of the materials are γw = 150 lb/ft3 and γst = 490 lb/ft3. The radii of thedowel and collar are shown.
1.Why is the compression test the one most frequently made for concrete? 2.Discuss why cross-sectional area of compression specimens must be larger than those of tension specimens. 3.Can you think of any instances where materials are intended to fail in compression *Need it asap,tnx
strength of materials... answer only A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 34 mm from the top of the of the beam on a section 1.66 m from A if P = 5381 N, W = 2349 N/m, a = 1.31 m, b = 2.12 m, c = 1.27 m, L = 72 mm and h = 239 mm. Round off the final answer to two decimal places.
A column has a radius of 150 mm and a height of 3 meters. The density of concrete is 2.45 Mg/m^3. Determine the weight of the column in pounds.
What can you conclude if we obtain a splitting strength of 1.41 N/mm^2 of concrete. What would be the effect if this concrete is used in construction works
A steel pipe having a length of 3 ft, an outside diameter of 5 in., and a wall thickness of 1/2 in. is subjected to an axial compression of 50,000 lb. Assuming a modulus of elasticity of 30 * 106 psi and a Poisson’s ratio of 0.27, finda. the shortening of the pipe,b. the increase in the outside diameter, andc. the increase in the wall thickness.
For steel: E = 200 x 109 N/m3 α = 11.7 μm/(m-°C) For aluminum: E = 70 x 109 N/m3 α = 23 μm/(m-°C) SHow your complete solution.
Recently, they have had some problems with their steel and look into some failures. The most probable strength of a steel beam is given by 24Y ―0.05 kips where Y is the number of cycles. This value is known to be 25% with 90% confidence.a) How many cycles will elapse before the beam loses 20% of its strength?b) Suppose the cyclic load on the beam is 10 kips. How many cycles will occur before the probability of failure reaches 10%? Assume this can be described by a lognormal distribution.
Getting measurements from Figure 11.20, determine approximate values ofthe following items for plain concrete, concrete with 2% steel fibers, and concrete with 3% steel fibers:a. Modulus of elasticityb. Ultimate strengthc. Strain at failured. Toughness. Curves may be approximated with a series of straight lines.e. Comment on the effects of increasing the steel fiber content on items a, b,c, and d above.
Given for a set of aggregates: A=2030.9, B 2044.9 and C=1304.3 A = Oven dry weight B = SSD weight. C = Weight in water Find the Bulk Specific Gravity, Bulk SSD Specific Gravity, Apparent Specific Gravity and Absorption