choose correct option nd do exolain plz QUESTION 14A non-potable water storage tank is at an elevation of 37 feet above the discharge for refilling water trucks. It has a square edged entrance (k =0.5). A 12-inch diameter pipe (e = 0.0018 inches) of 788 feet in length is used. There is a check valve (k = 2.5) and two elbows (k = 0.4).What flow rate can you expect to get from this hose to fill trucks?%3DO a. 1,010 GPMO b.2,785 GPMOc 4,310 GPMO d. 6,700 GPM

Given that, Elevation of the tank, H=37 ft,k of the entrance=0.5,Diameter of the pipe, D=12 in=1…

Answered: choose correct option nd do exolain plz

Engineering

Mechanical Engineering

choose correct option nd do exolain plz

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Need detailed solution. During a trip to the beach (Patm = 1 atm = 101.325 kPa), a car runs out of gasoline, and it becomes necessary to siphon gas out of the car of a Good Samaritan. The siphon is a small-diameter hose, and to start the siphon it is necessary to insert one siphon end in the full gas tank, fill the hose with gasoline via suction, and then place the other end in a gas can below the level of the gas tank. The difference in pressure between point 1 (at the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the higher to the lower elevation. Point 2 is located 0.75 m below point 1 in this case, and point 3 is located 2 m above point 1. The siphon diameter is 5 mm, and frictional losses in the siphon are to be disregarded. Determine (a) the minimum time to withdraw 4 L of gasoline from the tank to the can and (b) the pressure at point 3. The density of gasoline is 750 kg/m3. Answer: Δt = 53.1 s, P3 = 81.1 kPa
1) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 2) The EGL is always a distance V2/2g above the HGL. True or False
A centrifugal pump is used to pump water through horizontal distance of 150 meters and then raised to an overhead tank 20 meters above. The pipe is smooth with inside diameter of 50 millimeter. The pump head (meter of water) that will be generated at its exit to deliver water at a flow rate of 0.001 cubic meter per second is Blank 1 meter of water. Use fanning friction factor = 0.0062 Express your answers in whole siginificant figure without decimal value and without unit
the hydraulic radius of a pipe with a diameter of 12mm is
Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? Indicate the Free Body Diagram
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
kindly help me with this problems INSTRUCTIONS: Solve the problems neatly and systematically. SUse free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 1. A water from Agno River is pumped using a submerged pump at an efficiency of 78% that is discharged to aswimming pool in Itogon which has a free surface of 30 m above the Agno River water level. The pipe that wasused has a diameter of 7 cm on the suction line and 5 cm on the discharge line from the pump. If the powerrequirement of the pump is 5 kW assuming that the elevation difference between the pump inlet and outletand the effect of the kinetic energy correction factors are negligible, calculate for the followinga) Power requirement by the pump in kWb) Pressure difference across the pumpc) Pumping cost/day(24 hour) if the electricity cost is ₱2.00/kW-hr
In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a commercial steel pipe with an inner diameter of 23.62 inches carries a water flowrate of 600L/sec. The total length of the section is 10m. What is the frictional loss in meters of water at a temperature of 68o F?
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
What is the hydraulic radius of a circular pipe that is half full with water?
QUESTION 5 A reservoir discharges into another reservoir via a 3.2 km long pipe that has a pipe diameter of 300 mm. The pipe has a friction factor of 0.02 (Darcy). The difference in water level between the two reservoirs is 4.5 m. Determine the flow rate.
The system shown below uses a pump to transfer heavy fuel oil (T= 25°C) from the lower tank to the upper tank at the rate of 3600 L/min. All pipe is DN 100 Schedule 40 steel (total system length of 310 m) and the pressure line has two 90° long radius elbows and two 45º standard elbows. Valves are: fully open gate valve(s); 2 swing-type check valve, fully open butterfly valve. Determine: a. The head loss in meters due to pipe friction. b. The head loss in meters due to minor losses c. The required pump power in kW. d. The pressure at the pump inlet (suction line is 10 m long). Is this pressure a vacuum? e. The pressure at the pump outlet.