A short rectangular column 300 mm on one side and 400 mm on the other side is reinforced with 10-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. Use fc = 21 MPa and fy = 420 Mpa. Calculate the service axial dead load the column can sustain if the service axial live load is twice the dead load. Use reduction factor of 0.65

A short rectangular column 300 mm on one side and 400 mm on the other side is reinforced with 10-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. Use fc = 21 MPa and fy = 420 Mpa. Calculate the service axial dead load the column can sustain if the service axial live load is twice the dead load. Use reduction factor of 0.65

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter2: Concepts In Structural Steel Design

Section: Chapter Questions

Problem 2.1P: A column in a building is subjected to the following load effects: 9 kips compression from dead load...

See similar textbooks

Similar questions

A circular tied column 490mm in diameter is reinforced with 10-20mm-diameter vertical bars. Calculate the design axial strength of the column in kN. Use material strengths f'c = 26 MPa and fy = 420 MPa.
A beam section is shown in the figure. The beam will be subjected to a maximum service dead load of 215 kN.m. (including its own weight). Use f’c = 21 MPa and fy = 415 MPa. a.) Determine the effective depth of the beam. b.) Determine the distance of the neutral axis to the extreme compression fiber. c.) Determine the safe live load moment for this beam.
A 115mm thick concrete slab is supported by beams 300mm wide with effective depth of 650 mm. The beams are 8m long, spaced 4m on centers, and reinforced with six 28-mm diameter bars. use f'c=21 Mpa and fy=350 Mpa. 1. Compute the effective flange width in mm. 2. Compute the depth of the compression block in mm. 3. Compute the ultimate capacity of the beam in kN-mm.
A rectangular doubly-reinforced beam 450 mm wide and reinforced by 5-32mm diameter bars for tension and 3-28 mm diameter bars for compression and has the following properties: (NSCP 2010) d = 650 mm d’ = 70 mm f’c = 20.7 MPa fy = 344.80 MPa a. Find the depth of compression block. b. Find the ultimate moment capacity of the beam.
The uniformly distributed live load on the floor plan in Figure P2.4 is 60 lb/ft2 . Establish the loading for members (a) floor beam B1, (b) floor beam B2, (c) girder G1, and (d) girder G2. Consider the live load reduction if permitted by the ASCE standard.
A column 3m. high has a hallow circular-section of external diameter 300 mm. and caries an axial load of 5000 Kn. if the stress in the column is limited to 150 MPa and the shortening of the column under the load must not exceed 2 mm. Calculate the maximum allowable internal diameter. Take E=200 GPa.
A rectangular beam of length 702mm has a width of 132mm and a depth of301mm. Compression steel bars are placed at a distance 98 mm from the extreme concrete compressivefiber. The beam supports service dead loads of dead load (16 KN/m) and live load (24 KN/m). Reinforced with 4 25mm tension steel bars and 4 12mm tension steel bars f′c = 42 MPafy = 519 MPa 1. Solve for the height of the neutral axis measured from the extreme compression fiber.2. Solve for the design moment.3. Solve for the strength reduction factor.
A concrete framework is used to support a 125 mm reinforced concrete slab thatcarries a uniform live load of 12 kN/m2. The concrete density is 24kN/m3. The sizeof beam is 200 mm x 350 mm.There is a 125 mm thick brickwall on beam AD andCD. The walls are 3 m in height. Show the calculation of the design load of ColumnD in Figure 1.
The uniformly distributed live load on the floor plan in Figure P2.9 is 100 lb/ft. Establish the live loading for members (a) floor beam BI, (b) floor beam B2, (c) girder G1, and (d) girder G2. Consider the live load reduction if permitted by the ASCE standard.
1.Compute the initial effective length factor.0 2.Compute the stiffness reduction factor.0 3.Compute the final effective length factor about the x-axis.0 4.Determine the allowable axial compressive design strength of column AB in KN.0
A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for tension. Using an effective depth of d = 450 mm, determine if the 2.50 m long beam is adequate to carry a uniform load of 15 KN/m and a concentrated load of 10 KN at the cantilever end in 2 ways. Use f’c = 21 MPa, fy = 275 MPa. Neglect the weight of beam. Use n = 9.Determine if the catilever beam is adequate based on strength design 2001 NSCO specifications. The 15Kn/m load is DL while the 10KN load is LL.
A reinforced concrete column carries an axial dead load of 650 kN and an axial live load of 800kN. f’c = 28 MPa, fy = 400 MPa, steel ratio is 2%, and concrete cover is 40 mm. a. Design a square tied column.b. Design a round spiral column.