Problem 10.96The pendulum consists of a disk having a mass of 7 kgand slender rods AB and AC which have a mass of2 kg/m.(Figure 1)Figure 10.2 mAof 10.8 m0.5 m-DBPart ADetermine the length L of DC so that the center of the mass is at the bearing O.Express your answer to three significant figures and include the appropriate units.L =SubmitIo =μASubmitValueMy Answers Give UpPart BWhat is the moment of inertia of the assembly about an axis perpendicular to the page andpassing through point O?Express your answer to three significant figures and include the appropriate units.UnitsμAValueUnits?My Answers Give Up?

The pendulum consists of a disk having a mass of 7 kg and slender rods AB and AC which have a mass of 2 kg/m. (Figure 1) Figure 1 0.2 m of 1 0.8 m < -0.5 m-D Part A Determine the length L of DC so that the center of the mass is at the bearing O. Express your answer to three significant figures and include the appropriate u L= Submit μA Value Units My Answers Give Up ? Part B What is the moment of inertia of the assembly about an axis perpendicular to the pag passing through point O? Express your answer to three significant figures and include the appropriate u

The pendulum consists of a disk having a mass of 7 kg and slender rods AB and AC which have a mass of 2 kg/m. (Figure 1) Figure 1 0.2 m of 1 0.8 m < -0.5 m-D Part A Determine the length L of DC so that the center of the mass is at the bearing O. Express your answer to three significant figures and include the appropriate u L= Submit μA Value Units My Answers Give Up ? Part B What is the moment of inertia of the assembly about an axis perpendicular to the pag passing through point O? Express your answer to three significant figures and include the appropriate u

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the 2m x 5m gate shown in the figure. Pressure of air = 47 kPa Fluids: fluid a (s=3.8) fluid b (s=0.27) fluid c (s=1.68) h1= 0.9 m h2= 1.6 m h3= 3.9 m Round your answers in 3 decimal places
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
QUESTION 3: The radius of the flywheel given in the figure is 600 mm. Mass 144The rotation (inertia) radius of the flywheel, which is kg, is 450 mm. To a mass of 18 kgBody A is suspended on a rope wrapped around the flywheel. The system is sluggishHe is released in the (still) state. Body A 1.8 meters downFind the acceleration and velocity of the block when it moves towards.
The hanger for each chandelier in the grand ballroom of a five-start hotel is composed of 2m diameter ring weighing 2.5 kN/m and is supported by 6 rods such that said ring will be 3 m below the ceiling support. Find the vertical displacement of the ring. a. 6.17 mm b. 2.07 mm c. 3.09 mm d. 4.14 mm
Given beam loaded as shown below. Assuming EI is constant. 1. Which of the following gives the location of maximum deflection. a. 2.212 m b. 1.958 m c. 1.334 m d. 1.456 m 2. Which of the following the value of maximum deflection. a. 29.4/EI b. 17.5/EI c. 20.7/EI d. 14.2/EI
Two pipes, each 300m long 300 , are connected in series. The flow of water through the pipes is 150 L/s 0.15 with a total friction loss of 15m 15. If one pipe has a diameter of 300mm 0.3, what is the diameter of the other pipe? Neglect minor losses and assume f=0.02 0.02 for both pipes. Express your answers in 3 decimal places.
Show complete and detailed solution. Show FBD of the figure. What is the smallest mass of B to make the system in equilibrium while neglecting the friction between the string and the ramp? Mass of Block A = 45kg Coefficient of Block A, Block B, and Ramp C = 0.10
The step pulleys shown in the figure below are connected by a crossed belt. If the angular acceleration of C is 2 rad/s^2, what time is required for A to travel 180ft from rest? Through what distance will D move while A is moving 240ft/s? Answer for tA should be 6.71 sec and SD should be 180 ft
The pulleys are frictionless and of negligible weight. Determine the accelerations of block B and block A. Acceleration of block B=?Acceleration of block A=? Choices: 0 m/s^24.19 m/s^26.99 m/s^9.41 m/s^23.87 m/s^25.61 m/s^27.87 m/s^22.45 m/s^28.88 m/s^2
An elevator weighing 9.8 KN moves downward from rest until itattains a velocity of 20 m/s after it travels a distance of 5 m. Whatis the travel time of the elevator at this instant?a. 3 secsb. 2 secsc. 1 secd. 0.5 sec
A rectangular box is floated. Outer dimensions 2m by 10m and has 2m high sides and weighs 4.9N. It carries a load of 4.9N. It is launched in a pool of water with density 1 g/cm3. How much (in m) of the boat submerged (actual draft)? Provide the answer in appropriate precision (significant digits).
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. a. If a single pump is used to deliver water to a system which requires a total of 8 ft3/s, what is the efficiency of the pump (in %)? Take the specific weight of water to be 62.4 lbf/ft3. b. If two of these pumps are connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pump? Assuming the head is equally divided between the two pumps, what is the efficiency of either pump (in %)? Take the specific weight of water to be 62.4 lbf/ft3.