For the forces acting on the beam shown in Figure 3.1c, determine the location of the equivalent resultant force with reference to point A in m. Given a = 2.5, b = 2, P1 = 20, w1 %3D = 5 and w2 = 9. (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant force is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W2 kN/m W, kN/m A a m b m Figure 3.1c

For the forces acting on the beam shown in Figure 3.1c, determine the location of the equivalent resultant force with reference to point A in m. Given a = 2.5, b = 2, P1 = 20, w1 %3D = 5 and w2 = 9. (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant force is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W2 kN/m W, kN/m A a m b m Figure 3.1c

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
Determine the vertical displacement of joint C of the steel truss shown inFig.a. The cross-sectional area of each member is A = 400 mm2, and Est = 200 GPa.
If FA = 7 kN and FB = 5 kN, represent the force system acting on the corbels by a resultant force, and specify its location on the x–y plane.
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Determine the horizontal component of the force applied by the smooth circular guide on the mass A. mA = 2 kg, y= 100 mm, Vy = 0.6 m/s, ay = -0.2 m/s^2
A 140 KN force with a slope of 4 vertical and 7 horizontal islocated on the second quadrant. Determine its y- component.a. 121.55 KNb. 69.46 KNc. 112.55 KNd. 96.46 KN
For the truss shown, determine the maximum axial stress experienced. P= 70 Ex. (1.5P) = 1.5(70) = 105 (2.5P) = 2.5(70) = 175 All cross-sectional area is 300 sq. meter. P is in kN
Instructions: Follow Given-Required-Solution format for your computation. Complete FBD for full credit. Problem: The resultant of the three forces in the force R = -170j kN acting through point B. Determine P1, P2, and P3.
Determine the vertical displacement of joint C of the truss as shown. Assume that A = 0.5 in2 and E = 29(103) ksi.
Compute vertical displacement of E if: 100 kips acts dowmward at A A unit force acts down at E
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN