Q.1) Three forces and a couple moment are applied to an angle bracket as shown. The 50 lb force acts along the line passing through points A and C. a) Replace the force and couple system with a single resultant force and couple moment acting at point B. b) Replace the force and couple moment system with the simplest resultant force system and specify where its line of action intersects the line containing AB and the line containing BC, measured from point B. c) Make a sketch of the angle bracket with simplest resultant's line of action including dimensions from each intersection point found in part (b) with respect to point B. 100 lb 80 lb-ft 12 in B 65 lb 60° 9 in 50 lb

Q.1) Three forces and a couple moment are applied to an angle bracket as shown. The 50 lb force acts along the line passing through points A and C. a) Replace the force and couple system with a single resultant force and couple moment acting at point B. b) Replace the force and couple moment system with the simplest resultant force system and specify where its line of action intersects the line containing AB and the line containing BC, measured from point B. c) Make a sketch of the angle bracket with simplest resultant's line of action including dimensions from each intersection point found in part (b) with respect to point B. 100 lb 80 lb-ft 12 in B 65 lb 60° 9 in 50 lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q- The plan of a map was photo copied to a reduced size such that a line originally 100mm, measures…

A: Given data- Original line length = 100 mm, Measured length = 90 mm, Original scale of plan = 1 :…

Q: R.L. of point 'A' is 50 m and R.L. of point 'B' is 46.655 m. The distance between AB is 150 m. The…

A: Given :- R.L. of point 'A' = 50 m R.L. of point 'B' = 46.655 m. The distance between AB = 150 m. To…

Q: Given the two orthogonal projections of the object (top view and front view), identify the third…

Q: Draw the influence lines for Ay and By, Also for the shear and moment at point P X = 1.3m Y = 1₁/m…

Q: - Present a design proposal, utilising a selected alternative construction method, and explain how…

A: 1. Design Proposal: Utilizing Straw Bale Construction for a Community Center Alternative Method of…

Q: SIT 11. For the given figure below. El=constant. Use Slope Deflection Method 20 KN- 10 kN- ΒΕ 2 m 2…

Q: A reinforced concrete tower is provided on a ring foundation of inner radius of 8m and outer radiu…

Q: With aid of diagram, elaborate on the method to test material hardness using Brinell hardness test

A: Brinell hardness test:- The Brinell hardness test is a common method used to determine the hardness…

Q: a. The critical load for buckling is inversely proportional 3.00 feet long and 2.00 inches in…

A: Answer (a) In order to derive the equation based on the laboratory data we have Euler's critical…

Q: 3. Water is being pumped at 2.5ft3/s. The head loss between points 1 and 2 is 9ft and the power…

A: Given data: Flow of water pumped by the pump: Q=2.5 ft3/s Head loss between point 1 and 2 = hL=9 ft.…

Q: Q1. Compute ø for the following three cases: 650 mm 600 mm -350 mm- 44 4 fy=275 MPa f'c= 37 MPa 3…

Q: Design a laboratory scale chemostat to aerobically treat a 10 liters per day of a synthetic…

Q: Design a fillet welded joint to join two plates each of thickness 10 mm and 250 mm width for 100%…

Q: Pr Plot mon system. Find the moment of inertia of the shaded area about the horizontal and vertical…

Q: Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E =…

A: Given, Est = 29 x 106 psi αst = 6.5 x 10-6/°F Ebr = 16 x 106 psi αbr = 9 x 10-6/°F

Q: An air stream flows over a smooth plate with Reynolds number of 106. The boundary layer can be…

A: Given- Reynold's number Re=106, Turbulent boundary layer over the entire plate- Length of plate…

Q: ESSAY TYPE: As a Civil Engineering student, why do we need to undergo this course (geology)? Why is…

A: Importance As a civil engineering student, geology is an important subject that should be studied as…

Q: The surface of a saturated clay deposit is located permanently below the groundwater table. The clay…

A: Given: The clay has natural water content = 43 % Specific gravity = 2.70 The vertical intergranular…

Q: Problem No. 2 For the beam shown below has the following properties E = 350,000MPa 440x10 mm4…

A: As per company's guidelines we can only answer first question. Kindly post other questions as…

Q: For the shown structure, AB is made by C83400-red-brass (Ebr = 14600ksi, apr = 9.8 x 10-6/°F) and BC…

A: Given data: Member-AB [Red brass] Ebr=14600 ksi αbr=9.8*10-6 /°F Member-BC [Aluminium] Eal=10600 ksi…

Q: = Consider the following hydraulic structure formed on sand: T 5 m 5 m 5 m2m -5 m 4 m The uplift…

Q: Compute the maximum shear stress and maximum. flexural stress of the beam shown in the figure.

A: Given Data Determine the maximum shear stress and maximum flexural (bending) stress.

Q: A 1,100-N uniform boom at p = 67.0° to the horizontal is supported by a cable at an angle = 23.0° to…

A: Given, M = 1100 N ϕ = 67o θ = 23o W = 1750 N

Q: Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the…

A: Given data: h1=0.9 m h1=1.6 m h1=3.9 m Width of the gate, b= m depth of the gate, d=5 m Angle θ=60°…

Q: A semicircular plate with radius 10 m is submerged vertically in water so that the top is 3 m above…

Q: A T-beam with the cross-section shown above is subject to the loads shown. a) Determine the second…

A: Given:- To find:- Second moment of area SFD and BMD Normal stresses at A, B and C Concept:-…

Q: The couple M acts in a vertical plane and is applied to a beam oriented as shown. Determine the…

A: A couple, M is applied in the vertical plane. M = 300 kip-in The dimensions of the cross-section are…

Q: If a single pipe of length L and diameter D is to be replaced by three pipes of same material, same…

A: Given data- Single pipe length = L, Diameter = D, Three pipes of same material, same length and…

Q: For a turbulent boundary layer (under zero pressure gradient), the velocity profile is described by…

A: Given- A turbulent boundary layer (under zero pressure gradient)- Velocity profile is 1/5th power…

Q: 10.The entrance "P" to a mine tunnel is 40 m. from the nearest point of a railroad track. It is…

Q: Determine the determinacy of the following structures: a) b) c) Beam Hinge Frame Truss Hinge Hinge

A: Given:- A beam, frame, and truss structures are given:- To determine:- The determinacy of the given…

Q: A uniform symmetrical beam is supported at two pin joints as shown below. It has a length L and a…

Q: X Do the influence lines for Ay and Ma. Also for the shear and moment at point P. x = 0.9m y = 1.8m

A: Given data in question Cantilever beam Span 2.7 m To find out ILD for Ay , Ma , Sp & Mp Note…

Q: = Consider the following hydraulic structure formed on sand: T 5 m 5 m 5 m2m -5 m 4 m The uplift…

Q: A high-strength bolt that is passing through a steel plate is subjected to a tension force of P=4.6…

A: A) Given Data: Diameter of the bolt is db=12 mm. Diameter of the hole is D=14 mm. The tensile force…

Q: Determine the elastic curve equation, the slope at B and the deflection at C by double integration…

Q: e dependable flow of a river is 3 m³/s and the water duties at the system and farm levels are 2.5…

A: Given data, Dependable flow = 3 m³/s Duty at system = 2.5 lps/Ha Duty at farm level = 1.5 lps/Ha

Q: 5.10 An 18-ft- (5.4-m-) span simply supported beam carries a uniform dead load of 4 K/ft (60 kN/m)…

Q: A uniformly distributed load of 5 kN/m covers left half of the span of three- hinged parabolic arch,…

Q: Suppose there are three rivers (River A, River B, and River C) that have the same characteristics…

A: Given: Critical point for river A = 20 km Critical point for river B = 22 km Critical point for…

Q: A beam 4m long is simply supported at its ends. The beam is loaded with a downward vertical load…

Q: A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and…

Q: Determine the member face of the given truss. 30KN G A 20kn #f B , чт ни ди 20KN D 211 T Im T 2m +

Q: Why is it important for civil engineers to strive to comply with the principles of sustainable…

A: It is important for civil engineers to strive to comply with the principles of sustainable…

Q: 2.61. The following (MPN) test results were obtained for three water samples. Determine the MPN/100…

Q: 5.4 Assuming a density of 120 #/ft.³ for masonry brick- work, determine the maximum height of a…

Q: Solve the following reactions

Q: A base line was measured with a steel tape of designated length 30 m at 20°C at a pull of 100 N. The…

Q: Problem 3 The shaft consisting of steel and aluminum segments carries the torque T and 2T. Find the…

Q: During a particular stage of the growth of a crop, consumptive use of water is 3 mm/day. If the…

A: Given that :- Consumptive use of water = 3 mm/day if the amount of water available in the soil is…

Concept explainers

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.

Question

Q.1) Three forces and a couple moment are applied to an angle bracket as shown. The 50 lb force
acts along the line passing through points A and C.
100 lb
a) Replace the force and couple system with a
single resultant force and couple moment
acting at point B.
b) Replace the force and couple moment system
with the simplest resultant force system and
specify where its line of action intersects the
line containing AB and the line containing BC,
measured from point B.
c) Make a sketch of the angle bracket with
simplest resultant's line of action including
dimensions from each intersection point found
in part (b) with respect to point B.
80 lb-ft
12 in
65 lb
60°
9 in
50 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce the problem statement

VIEW

Step 2: Determine the resultant force

VIEW

Step 3: Determine the direction of resultant

VIEW

Step 4: Determine intercept of resultant from B

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

What are the units for the -0.7295 and 1.333?

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The overhead electric hoist C rides along a track on the horizontal beamAB. In addition to the 500-kN vertical force carried by the hoist, the beam alsosupports the three vertical forces shown. (a) If x = 5 m, determine the resultant ofthe four forces carried by the beam. (b) Determine the distance x for
Consider the object shown. Suppose that P = 390 N . Follow the sign convention. A) Determine the internal normal force at point C. NC = ? B) Determine the internal shear force at point C. VC = ? C) Determine the internal moment at point C. MC = ?
Ropes AB and BC are two of the ropes used to support a tent. The two ropes are attached to a stake at B. If the tension in rope BC is 490 N, determine (a) the angle between rope BC and the stake, (b) the projection on the stake of the force exerted by rope BC at point B.
Two forces act on the screw eye. If F1 = 400 N andF2 = 600 N, determine the angle θ (0° ≤ θ ≤ 180°) betweenthem, so that the resultant force has a magnitude ofFR = 800 N.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 4.5 ft, P = 21 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Express the moment of the couple acting on the pipe in Cartesian vector form. What is the magnitude of the couple moment? Take F = 125 N.
The force acting on the gear tooth is 20 N. a. What gives the component of the force along line aa? b. What gives the component of the force along line bb? c. If the component of force F acting along line aa is 30 N, determine the magnitude of force F.
Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent couple moment (Nm) acting at O if P = 507 N , Q = 382 N, and T = 451 N . Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of moment: use CW if clockwise , CCW if counterclockwise.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.4 ft, b = 3.5 ft, P = 30 kips, and w = 1.2 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Why is the force Fd pointing downwards? By force equilibrium, shouldnt it be 3 + Fd = 9 Fd = 6kN, thus pointing upwards?
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.