Classify the soil by IS classification Given:- Liquid limit=22% Plasticity limit=19% Percentage passing through 4.75mm IS sieve=98.5% Percentage passing through 75 micron IS sieve=35% D60=0.22 D30=0.19 D10=0.16

Classify the soil by IS classification Given:- Liquid limit=22% Plasticity limit=19% Percentage passing through 4.75mm IS sieve=98.5% Percentage passing through 75 micron IS sieve=35% D60=0.22 D30=0.19 D10=0.16

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter6: Soil Compaction

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Related questions

Q: A concrete is prepared by weight batching in the ratio 1: F: C with a water cement ratio of R. If…

Q: Given the following data from a differential levelling survey conducted in a certain road site,…

Q: Compound axial member ABC has a uniform diameter of d = 3.0 in. Segment (1) is an aluminum [E₁ =…

Q: lution so i c

A: Apply Bernoullis theorem P1γw+v122g+z1=P2γw+v222g+z2we knowP1=P2=Patm=0v1=0 (as large dia)

Q: A rectangular footing is to be used to support a 300 x 400 (400mm side is parallel to the long…

Q: Q1) For laminar flow conditions. Calculate the pipe diameter should be installed to carry 0.022m/s…

A: The given data is shown below: Q=0.022m3/sν=0.00021m2/sSG=0.9hf=20mLength of pipe=900m

Q: ar flow conditions. Calculate the pipe diameter should be installed to

Q: H.W1 The beam is subjected to the linearly varying distributed load. Determine the maximum…

A: step 1-

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0,0). After load P…

Q: A particle moves along the curved path shown. If the particle has a speed of 40 ft/sec at A at time…

A: Δθ=36-24180×π=0.1745RADvav=vA+vB2=40+452=42fps4=vB-vA=5fpsso,

Q: Design a sliding gate wing type of beams (w8*40) which have an elastic section modulus equal to 582…

Q: Given the following data from a differential levelling survey conducted in a certain road site,…

Q: gure fo

A: given:

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: For the given pin connected structure,

Q: If the gauge pressure and atmospheric pressure at a point are observed as 70 mm of mercury and 750…

A: Absolute Pressure = Gauge Pressure +Atmospheric pressure =70+750= 820 mm of mercury Absolute…

Q: 1. Figure 1 below shows a simple beam with two concentrated loads (X and Y). a. Write the shear and…

Q: through a pipe having an inside diameter of 60 mm Determine the Reynolds number

Q: If the capillary rise of water in a 1 mm diameter tube is 3 cm, the height of capillary rise of…

A: Height of capillary rise h=2σ cosθρgr h1r1=2σcosθρg=30*0.5= 15 mm2= h2r2 (As all the other…

Q: (1) why the flow faster at the pipe center when you observe few millimeters from the pipe inlet; (2)…

A: Uniform flow If the flow velocity have same magnitude and direction at every point in the fluid it…

Q: A construction project of cantilever sheet pile penetrating saturated clay is designed to form a…

A: Given Data:Sandγ=16KN/m3c'=0φ'=32L=2mSandγsat=19.35KN/m3c'=0φ'=32L=2mClayγsat=19.35 kN/m3C'=46.9…

Q: Problem 407 Beam loaded as shown in Fig. P-407. Figure P-407 3 m B 3 30 kN/m 2 m 1 m Ro

Q: carrying a variable load of w = 0 KN/m at the left support and w = 15 KN/m at the right. The beam…

Q: Q3/ Draw the relationship between the viscosity and temperature if you know th following below: 34…

A: given- Table for temperature and time is given.

Q: 3 = 20 L/s, μ =

Q: 1. Determine the reactions at supports. Find the rotation at point F and the maximu deflection of…

A: Given data: PL = 40kn UDL = 10kn/m

Q: Prob. 1. The 1.4- kip load P is supported by two wooden members of uniform cross section that are…

Q: Obtain the general solution of the DE: (xy + x) dx = (x²y² + x² + y² + 1) dy x)dx…

A: Given data: xy+xdx=x2y2+x2+y2+1dy

Q: 52. If the unsupported length of a stanchion is 4 meters and least radius of gyration of its cross-…

A: given- unsupported length Leff=4 m= 400 cmrmin=5 cm

Q: remove impurity from wastewater. Calculate effluent B.O.D of a two stage trickling filter with…

Q: Problem 1: A soil profile is shown in the figure. A uniformly distributed load of 4b kPa is applied…

Q: 2/104 The two cars A and B enter an unbanked and level turn. They cross line C-C simultaneously, and…

A: Given data:- Acceleration =0.9g RA=Radius of the curve of Car A =72 m RB=Radius of the curve of Car…

Q: F₁ A E * I I I A = 6500 mm² A=5200 mm² A= 3900 mm² The frame has the following wind loads: SET F1 F2…

Q: A cylindrical tank with flat ends has diameter of two meters and is 5m long. It is mounted on a…

Q: Group of answer choices

A: i) First take force summation along x; ii) then take force summation along y; iii) lastly take…

Q: A rectangular footing is to be used to support a 300 x 400 (400mm side is parallel to the long…

Q: An aluminum pipe has a length of 54 m at a temperature of 10°C. An adjacent steel pipe at the same…

Q: Problem 3: A consolidated-drained triaxial test was conducted on a normally consolidated clay with a…

Q: Question - 03: Please name the structural systems used in examples given below and compare them in…

A: Concept- There are several types of structures in the civil engineering projects. The major…

Q: Use the substitute member to make a complete analysis of the complex truss shown.

A: A truss is a structure in engineering that "consists of two-force members only, with the components…

Q: Two wooden members, each having a width of b = 6.9 in. and a depth of d = 2.3 in., are joined by a…

Q: 8-31. Determine the slope at B and the displacement at C. El is constant. Use the conjugate-beam…

Q: 8-27. Determine the displacement at C and the slope at B. El is constant. Use the conjugate-beam…

A: Determine the displacement at C and the slope at B.

Q: 1) For laminar flow conditions. Calculate the pipe diameter should b carry 0.022m³/s of heavy fuel…

A: Given:- v=0.00021m3/s s.g.=0.9 flow=0.022m2/s hf=20m L=900m To find:- d

Q: Determine the moments at B and C, then draw the moment diagram for the beam. All connections are…

A: Given- To find-Determine the moments at B and C, then draw the moment diagram for the beam. All…

Q: (d) A round bar shown in Figure 2b is mounted on the end of a motor shaft at its central fixing…

A: Given Data: Diameter of bar=0.1 m Length of bar=1m Speed(N)= 200 Rpm It is asked to calculate…

Q: a. Find the soil classification of soil A. b. Determine the soil classification of soil B. c. Find…

A: Given data-

Q: V A₂=0.02 m² 30° 60° A=0.01 m² This planar water (p = 1000 kg/m³) jet is deflected by a fixed vane.…

A: given- density (ρ)=1000 kg/m3velocity V=6.8 m/s

Q: Problem 7 - 72 Air at 1500 kPa absolute flows in a 25-mm-diameter tube. What is the maximum laminar…

A: The critical value for Reynolds number for which the flow can be laminar in case of pipe flow is…

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: Stress continues to rise to the point of fracture TRUE STRESS STRAIN CURVE O DESINE STRESS STRAIN…

A: Brief concept introduction- Point of fracture- It is the point on the stress-strain curve where the…

Concept explainers

Landfills

The landfill is a site used for the disposal of waste materials. The landfill is a solid waste facility that is often known as a dumping ground. The image below shows a landfill site in Hawaii. Landfilling is the most ancient and common method used for the disposal of waste. For the landfill, a deep trench is constructed in an isolated place away from the city. The trench for landfills is designed properly after analyzing the total population and the waste generation per capita. The waste is dumped into the trench and after every layer of waste, a layer of soil is spread on the top of it.

Question

Classify the soil by IS classification
Given:-
Liquid limit=22%
Plasticity limit=19%
Percentage passing through 4.75mm IS
sieve=98.5%
Percentage passing through 75 micron IS
sieve=35%
D60=0.22
D30=0.19
D10=0.16

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The section size of a water pipe is (100cm Χ 100cm), three types of soils A, B, and C are placed in the pipe, and a fixed amount of water is injected into the top left tap to keep the water head difference between the left and right ends of the pipe 60cm. The three soil permeability coefficients are k_A = 0.05 cm/sec , K_B = 0.1 cm/sec, k_C = 0.001 cm/sec, please calculate the following values:(1) The fixed amount of water injected into the faucet on the upper left (cm3/hr)(2) What is the total water head consumed by each of the three soils of A, B, and C (cm)(3) The overall volumetric seepage force of water flowing through the three soils (kN/m3)
In its natural state, a moist soil has a volume of 0.33 ft3 and weighs 39.93 lb. The oven-dried weight of the soil is 34.54 lb. If Gs=2.67, calculate total volume void in ft3 a) 0.2157 b) 0.2043 c) 0.684 d) 0.381
A container of volume 2.83 X 10-3 m3 weighs 9.8 N. Dry sand was poured to fill the container. Thecontainer and the sand weigh 52.3 N. Calculate (a) the void ratio and (b) the porosity. Describe thecondition of the soil (loose or dense). Assume Gs. = 2.7
4. A shrinkage limit test for a saturated specimen had the initial volume Vi = 21.35 cm3 and initial weight Wi = 37 gf ( = 37 × 0.00981 = 0.363 N). After drying, it became Vf = 14.3 cm3 and Wf = 26 gf (= 26 × 0.00981 = 0.255 N). Compute the shrinkage limit (SL) of this soil.
A sand with G, = 2.66 and e = 0.60 is completely dry. It then becomes wetted by a rising groundwater table. Compute the unit weight (lb/ft³ or kN/m³) under the following conditions: (a) When the sand is completely dry (b) When the sand is 40% saturated (S = 40%) (c) When the sand is completely saturated.
The Atterberg limits of a given soil are: LL= 68%, PL = 37% SL= 22%. If the natural moisture content of this soil at the site be 42%. Determine the Liquidity Index. a.0.298 b.0.839 c.0.456 d.0.161
For a soil with a specific gravity of 2.70, prepare a chart in whichunit weight (range of 10-25kN/m3) is plotted as ordinate and voidratio (0.2-1.8) is plotted as abscissa. Plot for three percentages ofsaturation 0, 50%, and 100%.
A soil specimen having a volume of 0.012 m3 has a specific gravity of 2.60. It has a moist mass of 20.6 kg and a dried mass of 16.1 kg. Compute its void ratio.
1. Calculate the amount of CaCO3 required to raise the pH of a hectare of this soil to pH6? (X-axis) Weight of lime added to 250g soil: 0,1,2,3,4,5. (Y- axis) pH: 3.58,5.05,6.56,6.76,6.94,6.96, respectively. 2. How many kg P/ha is 20 ppm P? ha= 2x 10^6; P= phosphorus
A WET OF SOIL SAMPLE HAS A VOLUME OF 4.85 x 10^-4 m3 AND WEIGHS 8.5N. AFTER OVEN DRYING, THE WEIGHT REDUCES TO 7.5N. IF sg = 2.7DETERMINE THE UNIT WEIGHT. DETERMINE THE MOISTURE CONTENT. DETERMINE THE DEGREE OF SATURATIONAnswer in 4 decimal places with unit
Subject Geotechnical engineering : soil mechanics A layer soil shown has the following data H1= 3m. K1= 2x10^-2 cm/sec H2= 4m K2= 3.2x10^-2 cm/sec H3= 6m K3= 4.1 x 10^ -2 cm/sec Compute the equivalent coefficient of permeability in vertical direction. Compute the velocity if h= 4m
For a soil, given e= 0.75, w= 22%, Gs= 2.66, calculate the dry density of soil in slug/ft3. Note ρ of water= 1.94 slug/ft3 a. 3.8 b. 2.95 c. 3.6 d. 2.85 With fbd if necessary