CO2 is needed in a surgical suite for abdominal laparoscopic surgery. You have already designed a nozzle to step down the pressure from the gas cylinder to the delivery hose. The well-insulated delivery hose has a 2.2 mm inner diameter. The inlet conditions to the delivery hose are 103 psia and 17°C. Typically, the surgeon uses 4 to 6 L/min of gas at pressures between 10 to 20 mm Hg to inflate the peritoneal cavity; however, the delivery system must be able to provide flow rate of 17.5 L/min at 20.0 mm Hg for safety. The surgeon will use a pin valve to control the flow rate and maintain the operating space. The gas temperature should not be any colder than 10°C when delivered to patient, or tissue damage might occur. Determine the acceptable delivery hose length to meet the surgical criteria. State assumptions.

CO2 is needed in a surgical suite for abdominal laparoscopic surgery. You have already designed a nozzle to step down the pressure from the gas cylinder to the delivery hose. The well-insulated delivery hose has a 2.2 mm inner diameter. The inlet conditions to the delivery hose are 103 psia and 17°C. Typically, the surgeon uses 4 to 6 L/min of gas at pressures between 10 to 20 mm Hg to inflate the peritoneal cavity; however, the delivery system must be able to provide flow rate of 17.5 L/min at 20.0 mm Hg for safety. The surgeon will use a pin valve to control the flow rate and maintain the operating space. The gas temperature should not be any colder than 10°C when delivered to patient, or tissue damage might occur. Determine the acceptable delivery hose length to meet the surgical criteria. State assumptions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It is proposed to pump 10,000 kg/h of toluene at 114°C and 1.1 atm abs pressure from the reboiler of a distillation tower to a second distillation unit without cooling the toluene before it enters the pump. If the friction loss in the line between the reboiler and pump is 7 kN/m^2 and the density of toluene is 866 kg/m^3, how far above the pump must the liquid level in the reboiler be maintained to give a net positive suction head of 2.5m?
10x106 ft3 of a gas at 60 °F and 760 mmHg must be delivered to a power plant per 24-hr day from a company 5 miles away. Delivery conditions are to be 60 °F and 10 psig at the plant. a. If the gas leaves the compressor at a temperature of 75 °F, what must be the pressure (in psia) at this point? The pipe is stainless steel with 20 inch Inner Diameter.
A two-stage, double-acting compressor is to deliver 90 lb/min of air from 14.3 psia and 90 ̊F to a final pressure of 185 psia. The normal barometer is 29.8 in. Hg and the temperature is 80 ̊F. The pressure drop in the intercooler is 3 psi and the temperature of the air at the exit of the intercooler is 90 ̊F, the speed is 210 rpmand pV1.34 =C during compression and expansion. The clearance is 5% for both cylinder. The temperature of the cooling water increase by 18 ̊F. Find (A) If, for the low pressure cylinder, L/D = 0.68 and if both cylinders have the same stroke, what should be the cylinder dimentions?
A centrifugal compressor draws in 240 m^3/min of air pressure of 96kPaa and a temperature of 15.6C. This air is delivered from the compressor at a pressure of 480kPaa and a temperature of 73C. The area of suction pipe is 0.2m^2, the area of discharge pipe is 0.037m^2 and the discharge pipe is located 6m above the suction pipe. The mass of the jacket water which enters at 15.6C and leaves at 43C is 307kg/min. Determine the power required to drive this compressor assuming no losses due to radiation.
The compression ratio of an air-standard gasoline engine is 7.5. The heat added is 1700 kJ/kg. If the initial pressure and temperature are 100 kPa and 27°C, respectively. Determine the temperature in °C at the end of the isentropic expansion.
An air compressor draws air from the atmosphere and discharges it at 500 kPa through a 100 mm-diameter outlet at 100 m/s. Determine the minimum power required to drive the insulated compressor. Assume atmospheric conditions of 25 C and 80 kPa.
Given that μ = 0.25Katm−1 for nitrogen, calculate the value of its isothermal Joule–Thomson coefficient. Calculate the energy that must be supplied as heat to maintain constant temperature when 15.0 mol N2 flows through a throttle in an isothermal Joule–Thomson experiment and the pressure drop is 75 atm.
3. A centrifugal compressor with 2.2 KW power operates with suction conditions of101 kPa absolute and 26 degree C. The pressure ratio for the unit is 3.2 and isentropiccompression efficiency is 72%. Determine the discharge temperature (actual)A. 416.87 K B. 462.71 K C. 436.87 K D. 446.71 K
Air at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass ﬂow rate 6 kg/s. The outlet pressure is 100 kPa and assume that speciﬁc heats are constant and evaluated at 600 K. 1. How much power is produced in kW? Round your answer to the nearest whole number. 2. What is the outlet temperature in K? Round your answer to one decimal place.
Calculate the amount of energy (kJ/kg) required to convert saturated water at 150 kPa to superheated steam at 170°C and at the same pressure.
R-134a enters a compressor as a saturated vapor at 80 kPa and exits at a pressure of 400 kPa. If 44 kJ/kg of work is required and 5 kJ/kg of heat is lost to the surroundings. What is the outlet temperature. Round your answer to the nearest whole number.
The enthalpy of steam entering the turbine inlet is 2750 kJ/kg and leaving turbine at 1750 kJ/kg. The enthalpy of saturated liquid is 190 kJ/ kg and enthalpy of dry saturated steam 2600 kJ/kg corresponding to the condenser pressure. The quality of steam at the exit of turbine is