Fora.10 H/p6 fit:Complete the following table.HoleShaftTolerance:Tolerance:Limit deviationsUpper deviation (ES):Lower deviation (EI):Upper deviation (ES):Lower deviation (El):Limit of sizeMaximumlimit of size:Minimum limit of size:Maximum limit of size:Minimum limit of size:FITType of Fit:МахMini.Go-No GO Gages for the above HoleComplete the following table.Show your calculation and draw Go -Not Go representation.Go Plug GageNOT Go Plug GageNominal size:Nominal size:Tolerance:Tolerance:Class:Max limit of size:Class:Max limit of size:Min limit of size:Min limit of size:

Answered: Image /qna-images/answer/8c5224c5-c841-4a49-ab0b-b65c6fbaf9f9.jpg

Answered: Complete the following table. Show your…

Engineering

Mechanical Engineering

Complete the following table. Show your calculation and draw Go -Not Go representation.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid
Pressure gages, such as the bourdon gage in Fig. , arecalibrated with a deadweight piston. If the bourdon gageis designed to rotate the pointer 10 degrees for every2 psig of internal pressure, how many degrees does thepointer rotate if the piston and weight together total44 newtons?
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V,pressure difference P, fluid density  and viscosity .a) (15P) Determine dimensionless  groups.b) (20P) A test is to be performed for a large pump that delivers 1.5 m3/s of water from 40 cmdiameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impelleris to be used. What flow rate should be used and what would be the pressure rise in model pump
Volumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V, pressure difference DP, fluid density r and viscosity m. a)Determine dimensionless P groups. b)A test is to be performed for a large pump that delivers 1.5 m3 /s of water from 40 cm diameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impeller is to be used. What flow rate should be used and what would be the pressure rise in model pump. Note: The model fluid is water at same temperature as the water in the prototype.
A 45 grams (0.045 kg) golf ball of diameter equal to 43 mm fell into a 2m deep lake. Neglect inertia at the moment of impact. Assume viscosity of 1.12x10-3 Ns/m2 , water density of 1,000 kg/m3 and Cd=0.5. Sphere volume equals 4π r³ /3. 1. How long will it take from the moment it hits the surface until it gets to the bottom? 2. If one estimates the Cd with Cd=24/Re formula, the settling velocity would be unrealistically large. Why?
Here, a 1:10 scale prototype of a propeller on a ship is to be tested in a water channel. What would the rotating speed of the model be if the rotational speed of the p propeller is 2000 rpm, and if: (a) the Froude number governs the model-prototype similarity(b) Reynolds number governs the similarity
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=1, theta1=0 degrees, L2=a=1.25, theta2=120 degrees, L3=b=1.5, L4=c=2 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.
An airplane builder wants to build a scaled-down model of a real airplane in a 12:1 ratio in order to be able to perform tests in a wind tunnel. The real plane flies at 126 km/h, while the air speed in the tunnel where the model is located is given by V. The performances of the two will be equivalent for a value of V, in m/s, equal to Data: air viscosity η = 1.8 × 10-5 kg/(m.s) air density ρ = 1.3 kg/m3
1. A lead cube has a total mass of 64 kg. What is the Length of its side in cm? specific gravity of lead = 7.27. 2. If the viscosity of water at 70 degrees celsius is 0.0077 poise and its specific gravity is 0.453, determine its kinematic viscosity in stokes.
Q2) Fill in the blanks with appropriate word(s), for EXKEl of the following; K Specific weight is defined as According to the variation of density with pressure, Nuids may be classified into - Nuids and - Nuids. 3. The approximate number of experiments to evaluate the influence of 3 parameters separately is assuming that 5 experiments are needed for each variable. ¿When viscous resistance is important, -. criteria for similarity is used. S. The center of pressure is defined as - A Hydrostatic forces in a static fluid is the result of the exerted on submerged surfaces. Streamline is defined as Continuity equation represents the d 0, conservation of
Given the following Atmospheric Data: Altitude (m) Pressure (kPa)0 - 101.331000 - 89.872000 - 79.503000 - 70.114000 - 61.66 Use linear interpolation to estimate the atmospheric pressure at: Altitude (m) Pressure (kPa)4MM ?2689 ?3500 ? (where MM is your birth month, so if you were born in December, evaluate at 312 meters)