Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=1, theta1=0 degrees, L2=a=1.25, theta2=120 degrees, L3=b=1.5, L4=c=2 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.

Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=1, theta1=0 degrees, L2=a=1.25, theta2=120 degrees, L3=b=1.5, L4=c=2 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=2.5, theta1=0 degrees, L2=a=2, theta2=45 degrees, L3=b=1.5, L4=c=1.5 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.
The following questions consider the stability of a floating iceberg. Approximate the iceberg as a perfect cylinder of uniform density, If the iceberg has a diameter of 3 meters and a length of 0.5 meters find the location of the metacenter as measured from the bottom of the iceberg. Take the density of sea water to be 1030 kg/m3 and the density of the ice to be 920 kg/m3.
J 5: !!!Please show it mathematically, not theory
Here are these questions if I could get help with themIf a spherical storage tank holds 40,000 gallons (120,000 liters) of water,what diameter must it have?If a cylindrical storage tank has a 40-foot (12 m) diameter circular 05::=how high must it be to hold 1 million gallons (3 million liters)?If water is moving at a rate of 3.2 ft3/sec (90,000 cc/sec), how manygallons (liters) per minute is this?If the specific gravity of gold is 19.0. what is the weight of a cubic inch(cubic centimeter) of gold? A cubic foot (cubic meter)?
A load weighing P kN aswith AB, AC and AD cables such asare carried. Points A and B are x-axis, Cand D points are on the y-z plane.Specific to your name in the data tableAB, AC and AD cable using ratingsCalculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 L4 (m) = 18 L5 (m) = 16 L6 (m) = 5
Q1. A line RS of 55 mm in length is inclined to HP by 30o and parallel to VP. One of its end points is above HP by 20 mm and in front of VP by 30 mm. The line is in single quadrant. Find the projections of the line RS and find out its horizontal trace.
. What force would be exerted against a seawall if a 1:36 model 0.914 m long experienced a wave force of 120 N?4. A surface vessel 156
How are you getting 16 mm at the end for an answer , "HX83=219X10^3/164.909".................is that your diving by f/a and multiplying by 83 to get H , im just no sure what you did to get 16 ?.
Find the magnitude of tension in string (or spring scale reading) and the magnitude of vertical FV and horizontal FH components of force applied on meter stick by the hinge. (Project this equation on Ox …this will give you the magnitude of FH force. Project this equation on Oy …this will give you the magnitude of FV force) (Draw a free body diagram) please data: Lruler = 1m mruler= 134 g dstring=80 cm d1= 35 cm d2= 82 cm M1=250g M2=150g θ = 38 degrees α= 62 degrees
1. What are the base units of the SI and U.S. Customary systems? 2. What is the definition of an angle in radians?3. Does the weight of an object depend on its location?4. If you know an object’s mass, how do you determine its weight at sea level? The Subject is Statics of Rigid Bodies
1. A non-uniform is 4.5m long and weighs 640N. It is balance when a 270N weight is hung 0.800m from the light end of the bar and the bar is pivoted at its center. Where is the center of gravity of the bar? 2.Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?