Complete the Servo motor lesson. Look up Servo PWM Timing. The servo motor receives a PWM like control pulse as an input. You send a pulse with duration of 1 ms every 20 ms, and the servo motor understands that the desired angle is 0 deg. If you send a pulse with duration of 2 ms every 20 ms, the servo motor understands that the desired angle is 180 deg. If the desired angle is 146 degrees, what is the duration of the input pulse in micro seconds? Round it off to a whole number.

Complete the Servo motor lesson. Look up Servo PWM Timing. The servo motor receives a PWM like control pulse as an input. You send a pulse with duration of 1 ms every 20 ms, and the servo motor understands that the desired angle is 0 deg. If you send a pulse with duration of 2 ms every 20 ms, the servo motor understands that the desired angle is 180 deg. If the desired angle is 146 degrees, what is the duration of the input pulse in micro seconds? Round it off to a whole number.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

For a dc machine, its commutator has a diameter of 50 c rotating at 1000 rpm. For a brush width of 1 cm, the time commutation taken by the machine will be _________a) 0.382 msb) 0.456 msc) 0.573 msd) 0.312 ms
Topic: TOPIC: Thyristors and Phase Control Study the thyristor's IV Characteristic Curve. Then try and explain it to your younger self. Why is the maximum firing angle of the AC resistance trigger circuit limited to 90 degrees?
A stepper motor has a step angle of 1.8o and is driven at 4000 pps. Determine (a) resolution (b)motor speed (c) number of pulses required to rotate the shaft through 54o.
A stepper motor has a step angle of 1.8º and is driven at 4000 pps. Determine (a) resolution (b) motor speed (c) number of pulses required to rotate the shaft through 75.6º.
Number of coil windings 300; slit width 12 mm How can I get the calibration factor by using ampere's law? Plz explain in detail
If a stepper motor travel 90º in 0.2s and operate at a pulse frequency of 3000 pps. What is the required resolution of the motor in SPR. Select one: a.1800 steps/rev b.2400 steps/rev c.3100 steps/rev d.4500 steps/rev e.5100 steps/rev
i) What is Electromagnetic Induction (EMI)? Differentiate a transformer with agenerator. ii) Richard is gliding on his skateboard at 4.0 m/s. He suddenly jumps backward off the skateboard, kicking the skateboard forward at 8.0 m/s. How fast is Dan going as his feet hit the ground? Richard’s mass is 50 kg, and the mass of the skateboard is 5.0 kg.
The Squirrel cage induction motor has less efficiency. Select one: True False
The ﬁeld current of an DC machine is supplied from an external DC source is called as, Separately Excited DC generator Shunt DC generator Self Excited DC generator Series DC generator
A 100 Hz ac circuit has a 300 ohm resistor, a 900 milli-henry inductor, and a capacitor all in series. The Capacitive Reactance is 165.49 ohms. The current from the source is 200 amps. Keep final answers to 2 decimal places. Use Pi = 3.14159 for all calculations. What is the value of the capacitor (in Scientific Notation)? What is the impedance of the circuit? What is the Inductive Reactance?
For the series RL circuit shown in the figure below, answer the following questions and justify your answer.If the current is kept constant, does the coil have inductance?If the current is kept constant, does the coil affect the current value?Can the reverse emf ever be greater than the battery emf?
An iron ring elecromagnet has a relative permeability of 1250 when it is excited by a coil having 500 turns at 0.8 A. the mean length of iron parts is 48 cm, the cross-section of the core is 10 square cm and the air gap is 0.5 cm. What is its total reluctance?