Compound axial member ABC has a uniform diameter of d = 1.0 in. Segment (1) is an aluminum [E1 = 10,000 ksi] alloy and segment (2) is a copper [E2 = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L1 = 66 in. and L2 = 110 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.45 in. L1 L2 (1) A d Aluminum (2) В Соpper Answer: kips P = i

Compound axial member ABC has a uniform diameter of d = 1.0 in. Segment (1) is an aluminum [E1 = 10,000 ksi] alloy and segment (2) is a copper [E2 = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L1 = 66 in. and L2 = 110 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.45 in. L1 L2 (1) A d Aluminum (2) В Соpper Answer: kips P = i

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
9. A compressive force of 15-N is applied to a flexible poly(vinyl chloride) (CAS# 9002-86-2) wire that is 5-m long and has a diameter of 3.6-mm. If the wire contracts by 0.5-mm, calculate the compressive modulus
A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and trunk onto a steel will 800.50 mm in diameter. The modulus of elasticity of steel is 200 GPa. 1) Which of the following most nearly gives the tensile stress in the tire. a. 145 MPa b. 130 MPa c. 110 MPa d. 125 MPa 2) Which of the following most nearly gives the compressive pressure between the tire and the wheel. a.) 4.35 MPa b.) 3.30 MPa c.) 3.90 MPa d.) 3.75 MPa 3) If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, which of the following most nearly gives its thickness. a.) 4.84 mm b.) 2.42 mm c.) 2.58 mm d.) 5. 16 mm
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
A central horizontal section of a hook is a symmetrical trapezium of inner width=67.5mm and of outer width =22.5mm. The depth of the section is 90mm. The hookcarries a load of 37.5kN. The load line passes through the centre of curvature. Theradius of the hook is 52.5mm. Determine the maximum compressive and tensilestresses in the section of the hook.
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.89 mm the values of elastic modulus for steel is 209 MPa. Take H1 = 7 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P in(N) = ii) Stress-induced in the top bar in(N/mm^2) = iii) Stress-induced in the bottom bar in(N/mm^2) =