Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 90 in. and L₂ = 130 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.30 in. L₁ L2 A Aluminum B (2) Copper CP

Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 90 in. and L₂ = 130 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.30 in. L₁ L2 A Aluminum B (2) Copper CP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

9. A compressive force of 15-N is applied to a flexible poly(vinyl chloride) (CAS# 9002-86-2) wire that is 5-m long and has a diameter of 3.6-mm. If the wire contracts by 0.5-mm, calculate the compressive modulus
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and shrunk onto a steel wheel 800.50mm in diameter. The modulus of elasticity of steel is 200gpa. Which of the following most nearly gives the comprehensive pressure between the tire and the wheel? A 3.30 mpa B 3.90 mpa C 3.75 mpa D 4.35 mpa
At 90 degrees of knee flexion, the mechanical stress at the tibiofemoral joint is 821.43 N/cm^2. If the compressive force is 1150 N, what is the magnitude of joint contact area (in cm^2)?
-Which of the following statement/s is NOT true?Strain is dimensionlessThe cross-sectional area affected by the rivets in a plate is πdtStrain is the total deformation of the body divided by its original length.Shear stress is directed parallel to the area upon which it acts. -Which statement is NOT true about ksi? *Kilo (psi).1000 lb1 x10^3 psi.1 x10^3 lb. -Tensile stresses and strain are considered:negative tensile stress and positive lengthnegative increase in lengthpositive increase in lengthpositive tensile stress and negative length
A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and trunk onto a steel will 800.50 mm in diameter. The modulus of elasticity of steel is 200 GPa. 1) Which of the following most nearly gives the tensile stress in the tire. a. 145 MPa b. 130 MPa c. 110 MPa d. 125 MPa 2) Which of the following most nearly gives the compressive pressure between the tire and the wheel. a.) 4.35 MPa b.) 3.30 MPa c.) 3.90 MPa d.) 3.75 MPa 3) If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, which of the following most nearly gives its thickness. a.) 4.84 mm b.) 2.42 mm c.) 2.58 mm d.) 5. 16 mm
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as floows; 48 kips tension in the x directio, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A straight bar 450 mm long is 10 mm in diameter for the first 200 mm length and 20 mm in diameter for the remaining length. If the bar is subjected to an axial push of 10 kN, determine decrease in length of the bar. Take modulus of elasticity of bar material E = 2 × 105 N/mm²