Compound axial mermber ABC has a uniform diarneter of d= 1.25 in. • Segment (1) is an aluminum (E, - 10000 ksi) alloy. The length of segment (1) is L1 - 100 in. • Segment (2) is a copper (E2 = 17000 ksi] alloy. The length of segment (2) is L2 - 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of €2 = 2300 uin/in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B (2) Соpрer Answer: AL - i in.

Compound axial mermber ABC has a uniform diarneter of d= 1.25 in. • Segment (1) is an aluminum (E, - 10000 ksi) alloy. The length of segment (1) is L1 - 100 in. • Segment (2) is a copper (E2 = 17000 ksi] alloy. The length of segment (2) is L2 - 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of €2 = 2300 uin/in. in the longitudinal direction. What is the total elongation of member ABC? L2 Aluminum B (2) Соpрer Answer: AL - i in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a uniform bar 1 is connected to a tapered rod 2. both are subjected to axial loads as shown. if P=7 kN, determine the axial deformation of tapered rod 2 (in mm). indicate negative sign if compression
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of tapered rod 2 (in mm). Indicate negative sign if compression.
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
The shaft shown consists of a steel tube (1) bonded to a brass core (2). The shear modulus of steel is 11,400 ksi and the shear modulus of brass is 5,200 ksi. A torque is applied at A. The radius of the brass core is 0.5 in. The outer radius of the steel tube is 1 in.d) Assume the allowable shear stress in the brass core is 450 psi. Calculate the maximum torque you could apply to the system in k-in.e) Assume that the maximum angle of twist at the free end is not to exceed 0.05 rad. Calculate the maximum torque you could apply to the system in k-in.f) Based on your answers from parts (c)-(e), what is tha maximum torque (in k-in) you could apply to the system using a factor of safety (FOS) of 2?
The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable shear stress of 6 ksi. The diameter of the rod is d1 = 0.500 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
ABD rigid bar with 40mm diameter BC bar at point B, It is supported from point A with a 30 mm diameter single action rivet. BC bar There are single action rivets of 40 mm diameter at both ends. On the BC bar maximum normal stress 250 Mpa, maximum shear stress in rivets Since it is 330 Mpa; a) Normal stress on BC bar b) Average shear stress at A and B rivets c) Calculate the safety coefficient FS on BC bar and rivets separately.
The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a diameter of 10 mm. Determine:a. The normal stress in bar AB. b. The shear stress of the bolt at C.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 110 GPa] with a cross-sectional area of A1 = 520 mm?. Bar (2) is an aluminum alloy [E = 67 GPa] with a cross-sectional area of A2 = 280 mm?. A concentrated load of P = 88 kN acts on the structure at D. Assume L1=800 mm., L2=390 mm., a=510 mm., b=300 mm., and c= 1130 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vo of point D on the rigid bar.
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the total axial deformation (in mm) Indicate negative sign if compression. Complete solution no rounding off.
From the following Pratt armor, determine the following: Reactions in A and E. The internal forces at node C. (Indicate whether the forces are in compression (C) or tension (T)). The internal forces in the elements GH. (Indicate if the forces are in compression (C) or tension (T)). Draw the respective free-body diagrams. Consider the following: - A and E are simple supports. (Check image el1 for the pratt armor) (Check image el1.1 for the values to solve the armor)
The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of aluminum (Eal = 70 GPa) and has a cross-sectional area of AAB= 400 mm2; Rod CD is made of steel (Esteel = 200 GPa) and has a cross-sectional area of ACD = 500 mm2. The load P = 31 kN is applied at point E as shown in the figure. [LAB = 0.3 m, LCD = 0.4 m, a = 0.2 m, b = 0.4 m] Determine the internal force of rod AB?KN Determine the displacement of point B?in mm Determine the displacement of point E?
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 94 GPa] with a cross-sectional area of A1 = 510 mm?. Bar (2) is an aluminum alloy [E = 74 GPa] with a cross-sectional area of A2 = 380 mm?. A concentrated load of P = 89 kN acts on the structure at D. Assume L1=770 mm., L2=620 mm., a=690 mm., b=350 mm., and c=1220 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar.