Compute ‘h’. Neglect the box type figure for the hydrometer as it is just used as weights of hydrometer to submerge itself in fluid.

Q: I The force on the 12mm thick link in the figure shown is 2960 N. If the pin has a diameter of…

A: Given,  Thickness = 12 mm Force = 2960 N Diameter of pin  = 10 mm

Q: The city of Chicago is an amazing outdoor museum of modern architecture. Pick one building from…

A: The city of Chicago is an amazing outdoor museum of modern architecture.

Q: Q.17 For a liquid velocity u varies with y as follows U = 3y - 6y² 2 U = m/s and y is in meter for Y…

A: Given data- Velocity variation- U=3y-6y2, Viscosity- μ=1 poise, To Find- The shear stress in the…

Q: Question A sanitary landfill has an available space of 12.5 ha for the dumping of solid waste. On…

A: Given- Available space = 12.5 ha for the dumping of solid waste. On average, 640 m3 of solid waste…

Q: 1.The Importance of horizontal curve and its types: simple curve, compound curve, reverse curve and…

A: The highway is set with curves, whether it is on the vertical plane or the horizontal plane, when…

Q: 12 The uniform crate shown in Fig. 8-7a has a mass of 20 kg. If a force P = 80 N is applied to the…

A:

Q: 14.1 What is the meaning of the acronyms CMU, URM, UMB?

A: To find : Meaning of acronyms CMU, URM and UMB

Q: Calculate the reactions and all member forces (moment, shear, axial) of the building frame using…

A: Answer  To determine the Moments , shear and axial forces using Portal method, we have two…

Q: Ex. A 4.0 m wide rectangular channel carries a discharge of 12.0 m³/s at a depth of 2.0 m. Calculate…

A:

Q: A mechanism is shown below. The number of tertiary links and the DOF, respectively are:

A: A ) To Find : Degree of freedom ? A problem of Structural Analysis.

Q: depth of 56 cm and an average velocity of 9 m/s undergoes a hydraulic jump. Determine the head loss…

A:

Q: A trapezoidal dam with vertical upstream face is 6m high, 0.6m at the top  and 3m wide of the…

A: 1 m = 1.094 yd 1 yd = 3 ft A trapezoidal concrete dam is given, Top width, b = 0.6 m = 0.656 yd…

Q: 17.3 A 1-in.-by-4-in. steel bar is subjected to the loads show Calculate the combined stresses at…

A: Given Data -  Cross section of Bar = 1 × 4 inch  Load P1 = 12000 lb . P2 =1200 lb  Find -  Combined…

Q: Solve the problem below. Provide a clean solution. Label each points from A to E then draw the load,…

A:

Q: - An aluminum right-circular cylinder surrounds a steel cylinder as shown. The axial compressive…

A:

Q: Question- For steady state flow to a fully penetrating well in a confined aquifer, the drawdown at…

A: Given data- Steady-state flow- Drawdown- S1=4.92 m, S2=5.45 m, Radial distance- r1=1.56 m, r2=1.80…

Q: At a municipal waste handling facility, 30 metric ton mixture of food waste, yard waste, and paper…

A: Solution is attached below as

Q: : The T-beams sections shown in the figures below. f'c-28 Mpa, fy=420 Mpa. Calculate the design…

A:

Q: The result of the liquid limit tests where N is the no of blows and w is the water content in % are…

A: Given  Trial no. of blow (N) water content (w)% 1 11 53.9 2 15 50.6 3 23 48.1 4 30 46 5…

Q: Calculate shear force and draw SFD and BMD using Moment Distribution Method

A:

Q: (a) Draw the influence diagram for the force in member CG. Plot tension as a positive value. Label…

A:

Q: A town with a population of 150000 people is supplied with water through a pipeline from a reservoir…

A:

Q: Discuss the Steps for Equipment Selection as well as Equipment Utilization in a 1000 bedded…

A: Steps for Equipment Selection: 1) Determining the need: Before purchasing any equipment, the primary…

Q: Determine the time of concentration for use in the Rational Method for a drainage basin having  the…

A: Average Grass Overland flow length, L = 80’ Slope, S = 2.5% Shallow Conc. L = 450’ S = 4.8%…

Q: 8 ft 8 ft 8 ft N A 900 lb L M. 8 ft B 1000 lb 1500 lb 8 ft 8 ft K 1000 lb 8 ft 8 ft 8 ft H A.…

A:

Q: 14.7 At the base of this CMU wall there are a series of wall cleanouts. What are they for and when…

A: The wall cleanouts are used in drainage piping where a cleanout is required concealed in walls.

Q: A simply supported beam having a span of 10m. carries a uniform load of 20 KN/m over its entire…

A: Given- Span= 10 m  UDl = 20 KN/m P    = 40 KN Fb = 0.60 Fy Fy  = 200 N/mm2    Solution, Lets…

Q: Determine the following using the conjugate beam method: a) Slope at D b) Displacement at end A EI…

A:

Q: 7. Will the soil represented by the solid line serve as a suitable filter for the soil represented…

A: To Determine :- Can the soil represented by the solid line serve as a suitable filter for the soil…

Q: Question 8 In a two-dimensional field the velocity of fluid flow is given by v = (y³ - 5x²y)i +…

A:

Q: A simply supported beam having a span of 10m. carries a uniform load of 20 KN/m over its entire…

A: Z

Q: A fixed time two-phase signal is to be designed for a four-legged intersection, for which the design…

A:

Q: What will happen to steel railroad tracks on a hot day if the tracks were laid out during a cold day…

A: As it is given that the steel track were laid out during a cold day without clearance or gap the we…

Q: Q2: Design the rectangular reinforced concrete beam shown in the figure to carry service loads of…

A: Given: DL = 10 kN/m LL = 15 kN/m L = 6 m Assume; fc = 25 MPa fy = 400 MPa

Q: (A) 62.5 MPa (B) 31.25 MPa 125 MPa -IN A load P is supported as shown by a steel pin that has been…

A: Given :short wooden member  Tensile Stress in wood= 60Mpa Shear stress in wood=7.5Mpa Allowable…

Q: At the outfall from a lake into a steep channel, the channel is of trapezoidal section with a base…

A: Given, b = 6 m  m = 2

Q: A short horizontal pipe connects the bottom of two tanks with axes vertical. One, a cylinder 8 ft.…

A:

Q: : The T- beams sections shown in the figures below. f'c-28 Mpa, fy=420 Mpa. Calculate the design…

A:

Q: QUESTION 6 A bar of uniform cross sectional area- 168.290 mm2 is fully fixed at supports A and B and…

A:

Q: Knowing that P = 5.4 kN, determine the factor of safety for the structure shown. Use E = 202 GPa and…

A: A) P = 5.4 kN E = 202 GPa To Determine : The factor of safety for the structure ? A problem of…

Q: where did you get the value 289 from the bending moment diagram?

A:

Q: A 50.0 kg crate is being pulled by a rope as shown. The height and the width of the block are 0.450…

A:

Q: 6. In a longitudinal profile, which is rotated at center lane. The height of the outer lane is 0.80…

A: given:  height of outer lane (h) = 0.8m superelevation (e) = 0.08 To find : width of road (w)

Q: Question 6 6. To find the distance across a small lake, a surveyor has taken the measurements as…

A:

Q: A transition curve is to be provided for a circular railway curve of 300m radius, the gauge being…

A:

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

A:

Q: A physically small (treat as a point mass) box weighing 80 lb is sitting on a floor. The…

A:

Q: What is the shear stress in the 25-mm diameter bolt at pin C if P = 25 KN? A 50.93 MPa B 67.91 MPa…

A: Given,  dc = 25 mm  P = 25 kN

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

A:

Q: Problem 2.y For the beam loaded as shown below, by the area-moment theorems, (AMM or AMT), determine…

A: Given To Find Slope and deflection at point A and C

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.