Compute the latitudes and departures for the sides of the traverse shown in the figure. Determine the error of closure and precision of the traverse. Note: there is an error in the textbook. The length of line CA should be 778.26 ft, with a bearing of N82º44'W (as shown in the figure below). N5613E 452.38 t 778.26 R N8244'W S4832E 528.49

Q: With the following information of a closed traverse, determine the bearing of line BC. AB: 44.47,…

A:

Q: Refer to the closed traverse image below (A-B-C-D-E-A). Measurements of the interior angles are…

A:

Q: Compute the latitudes and departures for the sides of the traverse shown in the figure. Determine…

A: Here, latitude= Length x Cos(bearing) Departure= Length x sin(bearing) The following diagram shows…

Q: A closed traverse has the following data: LINE / LENGTH (m) / Bearing AB / 126.00 m/ N 35° E BC /…

A:

Q: Determine the interior angles for the accompanying traverse sketch. N76 30'E N87°32'W D Note:…

A: Given:-  Determine the interior angles for the accompanying traverse sketch.

Q: Find the true course to steer if the compass course reads N 36°W, deviation 17°W, variation 39°E. а.…

A:

Q: From the field notes of a closed traverse shown below, adjust the traverse: LINES BEARING DISTANCES…

A: Step 1

Q: Using transit rule, adjust the closed traverse.Compute also the linear error of closure and the…

A: This approach was created to balance a traverse in which the angles are determined with more…

Q: The interior angle of a five sided closed traverse were measured as follows: A = 85°11', B = 68°30',…

A: We will determine the bearing in whole circle bearing system (WCB)

Q: Determine the interior angles of the given interior angle traverse. LINES BEARINGS АВ N76°30'E ВС…

A: Furstwe have to reduce quadrantal bearing to whole circle bearing for given 4 sided polygon  Then…

Q: The observed magnetic bearings of a closed compass traverse are as follows: Line Observed Bearing…

A: a. Compute the mis-closure of the traverse in degrees. b. Compute the adjusted interior angle at…

Q: Using the given data from the close traverse shown: POINTS BEARING AB N 30° E BC S 45° E CA Due West…

A:

Q: 1) Using transit rule , adjust the closed traverse.Compute also the linear error of closure and the…

A:

Q: 1. From the field notes of a closed traverse show below, adjust the traverse. LINES BEARING…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: 1. The interior angle of a six-sided closed traverse were measured as follows: A 36 54' 23 B = 145…

A: Given  6 sides polygon  Interior angles of the polygon

Q: Given the following interior angles (angles-to-the-right) of a five-sided closed polygon traverse…

A:

Q: en the following interior angles (angles-to-the-right) of a five-sided closed polygon traverse and…

A:

Q: Problem 2. The interior angles of a five side traverse are as follows: A = 105°45' C = 87°52' The…

A:

Q: From the given data of a losed traverse. Distances (m) Bearing N 15°18' E S 85°46' E Lines АВ 368.76…

A: We have to determine the value of bearing of BC and bearing of CD and bearing DA as per the given…

Q: 1. What is the linear error of closure? a. 0.113 b. 0.250 c. 0.045 d. 0.453 2. What is the balanced…

A: rror of latitudes:∑ Lat=415-210.16-204.51=0.33Error of Departures:∑…

Q: The total error in the departure is -2.55m, while the sum of all positive and negative departures is…

A:

Q: A closed traverse has the following data: Line AB BC CD DA Length (m) Bearing 83.07 160.33 58.15…

A:

Q: Compute the bearings of all lines for a closed traverse ABCDEFGHA that has the following balanced…

A:

Q: 2. Given the observed magnetic bearings (forward and backward) of a closed compass traverse Line…

A:

Q: s traverse, the adjusted forward bearing of line BC is?

A: on looking at the noticed orientation of lines , it will be seen that contrast among back and front…

Q: Q5- For the closed looped traverse PQRS below, find:- 1. Closing error and relative accuracy. 2. The…

A: Given Data:PointsEast xNorth yP199.88300.24Q200275R144.02317.03

Q: Q1: for the traverse in the table below: 1- Draw a sketch 2- Balance the angles 3- Compute the…

A:

Q: 1. The following are bearings taken on a closed compass traverse. Compute the interior angles and…

A: The sum of all internal angle = (2n-4)×90o. Where n = number of sides or lines. Converting all the…

Q: Q5) If |BC| = 166.176 m , determine Azimuth (AB),|AB| and coordinates of point C %3D x=906.54m B…

A: coordinates at A=XA,YA=879.94,88.09  and  Azimuth =θABB=XB,YB=906.54,253.95  and  Azimuth…

Q: A :51°23' AB 713.93 ft N 67°11' E В 105°39' ВС 606.06 ft A C = 78°11' CD 391.27 ft %D D = 124°47' DA…

A: Bearing is defined as the angel used in surveying for the instrument or the object. Surveying is a…

Q: 2) The followings are bearings taken on a dosed compass traverse.Compute the interior angles and…

A: For solving these one can follow the steps  we have to convert the given bearing into a whole…

Q: 1) Using transit rule , adjust the closed traverse.Compute also the linear error of closure and the…

A:

Q: d. Adjust the traverse using Compass Rule e. Adjust the traverse using Transit Rule BEARING DISTANCE…

A:

Q: PROBLEM #3 Given the closed traverse, a.) Draw a sketch of the traverse with points and angles b.)…

A: To find Draw sketch of traverse. Computation of angular error and adjustment. Computation of…

Q: A closed traverse has the following data: Line Distance (m) Bearing AB 895 S 70° 29′ E BC 315 S 26°…

A: Surveying, the initial step of beginning another structural designing venture, is a vital part of…

Q: 3. From the traverse shown below. Compute the following: a) Azimuth of side BC. b) Bearing of side…

A:

Q: Using the deflection angles shown, calculate North azimuths and Bearings of the lines. Show your…

A:

Q: From the field notes of a closed traverse shown below, adjust the traverse: LINES BEARING DISTANCES…

A: The concept used:-   Computing Latitudes:       Lat. = length x cos α Computing Departures :…

Q: 3 The four-sided closed traverse shown in the figure below has the following interior angles and…

A: a. Perform a check for angular closure and if necessary, balance the angles by applying equal…

Q: For the given data of a close traverse, determine the missing bearings of courses DE and EF then…

A: Traverse is a technique in the field of reviewing to lay out control organizations. It is likewise…

Q: $67°24″E 8. Given the following sketch and tabulated data for a closed traverse in which the length…

A:

Q: 11. In a given closed traverse, the sum of the north latitudes exceeds the sum of the south…

A: As a question is belong to surveying From the given data in  question Latitude: Projection of line…

Q: From the open traverse ABCDE shown below, determine the following: 4 86°08' 43 20 A E B 50 12' 35°35…

A:

Q: 1) Using transit rule , adjust the closed traverse.Compute also the linear error of closure and the…

A: Adjustment of Traverse by Transit Rule Latitude = Lcosθ Departure = Lsinθ Correction in LAT =…

Q: Q4-In the traverse below if the Azimuth of AB = 30° 30' 30" find the coordinates of point B and C В…

A:

Q: A closed traversed has the following data. LINE DISTANCE BEARING AB 185.33 N 43 E BC 258.28 S 67 E…

A:

Q: PRACTICE PROBLEM 1. The following are bearings taken on a closed compass traverse. Compute the…

A: As per internal angle method the sum of all the internal angle = (2n-4)×90o, where n = number of…

Q: 1. From the field notes of a closed traverse show below, adjust the traverse. LINES BEARING…

A:

Q: A traverse has the following data: DRAW THE TRAVERSE AND SOLVE THE FOLLOWING USING COMPASS RULE.…

A: Engineers use information such as lengths and angles between points and lines to determine how to…

Q: 8. Compute for the following and show the tabulated solutions: Azimuth LINES Length (S) AB 1020.87…

A: Solution Line Length Azimuth Latitude departure Correction Adjusted Adjusted Length Adjusted…

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.