Consider a computer “A” which is connected in a LAN transmission technology. Computer “A” transfers data from one computer to another computer using the address “3C:D9:2B:CB:AA:FC”. Identify which part of this address is specific to the Network Interface Card? Choose an answer A 2B:CB:AA B CB:AA:FC C 3C:D9:2B D D9:2B:CB

Consider a computer “A” which is connected in a LAN transmission technology. Computer “A” transfers data from one computer to another computer using the address “3C:D9:2B:CB:AA:FC”. Identify which part of this address is specific to the Network Interface Card? Choose an answer A 2B:CB:AA B CB:AA:FC C 3C:D9:2B D D9:2B:CB

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 3RQ

See similar textbooks

Similar questions

An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most signi cant bits are used as a network ID, and the 16 least signi cant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?
Consider a packet sent on a bridged LAN to a nonexistent address. Across how many segments will bridges forward the packet?
An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?
a.) Give one example of a unique type of address specifically used in each of the following layers: application layer, data-link layer, and network layer? b.) An ARP (Address Resolution Protocol) query is sent in a broadcast frame for what purpose? For the response, does the sending node need to send a broadcast frame to all the other nodes on the LAN again? why?
A local area network (LAN) makes use of something called a hub. Is there a route out of the collision zone that we don't have to go into? In the event that this is the case, could you kindly elaborate? In the event that this is not possible, what alternative types of technology are available, and how do they function?
Consider a IP address 201.24.58.69 in classful address, if the number of 1's in directed broadcast address is a and number of 1's in network ID, of the given IP address is b, value of a + b.
Consider a computer 1 that communicates with a computer 2 via LAN1, router R1, and LAN2. The sending computer1 is running two processes at this time with port addresses k and l. The receiving computer 2 is running three processes at this time with port addresses f, g and h. Process k in the sending computer 1 needs to communicate with process g in the receiving computer 2. Draw the network and show the contents of segments, packets and frames at the network, data link, and transport layer for each hop. Note: Computer 1 has: Physical address=15, Logical address=A Router R1 has: Physical address in the side of LAN 1=20, Logical address in the side of LAN1=B Physical address in the side of LAN 2=50, Logical address in the side of LAN2=D. Computer 2 has: Physical address=77, Logical address=E.
Suppose an application uses rdt 3.0 as its transport layer protocol. As the stop-and-wait protocol has very low channel utilization (shown in the cross-country example), the designers of this application let the receiver keep sending back a number (more than two) of alternating ACK 0 and ACK 1 even if the corresponding data have not arrived at the receiver. Would this application design increase the channel utilization? Why? Are there any potential problems with this approach? Explain
Consider sending real-time data from Host A to Host B over a packet-switched network. Host A takes an 8-bit measurement every millisecond, and Host A collects these into 64-byte packets. There is one link between Hosts A and B; its transmission rate is 5 Mbps, its propagation delay is 2 × 108 meters/sec, and its length is 3 km. As soon as Host A gathers a packet, it sends the packet to Host B. How much time elapses from the time that Host A begins to take the first measurement in a packet until the entire packet reaches Host B?
Consider the extended LAN connected using bridges B1 and B2 in the Figure given below. H1 shown in the figure is a hub which has the property of taking an input on one port and forwarding it on all other ports. Suppose the forwarding tables in the two bridges are empty. List all ports on which a packet will be forwarded by bridges B1 and B2 for the following sequence of data transmissions: a) A sends a packet to C b) E sends a packet to F c) F sends a packet to E d) G sends a packet to E e) D sends a packet to A f) B sends a packet to F
Let's imagine that one computer on the Internet is communicating with another computer by sending a packet across the network layer. The logical destination address of the packet has been corrupted due to an error that has occurred. Which address should I use for the shipment? When this takes place, how will the first computer learn about it?
b.) An ARP (Address Resolution Protocol) query is sent in a broadcast frame for what purpose? For the response, does the sending node need to send a broadcastframe to all the other nodes on the LAN again? why?