Consider a cylindrical tank that is completely filled with water. The cylinder has a radius of r = 2 m and a length of l = 7 m. Water exin here Calculate the work in megajoules (1 MJ =1 x 10º J) required to pump all water out of the tank. The density of water 1000 kg/m³. Assume g = 9.8 m/s². (Use decimal notation. Give your answer to three decimal places.) work:

Consider a cylindrical tank that is completely filled with water. The cylinder has a radius of r = 2 m and a length of l = 7 m. Water exin here Calculate the work in megajoules (1 MJ =1 x 10º J) required to pump all water out of the tank. The density of water 1000 kg/m³. Assume g = 9.8 m/s². (Use decimal notation. Give your answer to three decimal places.) work:

Name: Consider a cylindrical tank that is completely filled with water. The
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Consider a cylindrical tank that is completely filled with water. The cylinder has a radius of r = 2 m and a length of1 = 7 m.Water exits hereCalculate the work in megajoules (1 MJ = 1 × 10° J) required to pump all water out of the tank. The density

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 1RQ: Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop...

See similar textbooks

Similar questions

Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.6 m3/s and exits through a 25-cm-diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine– generator efficiency of 83 percent, determine the net electric power output. Disregard the effect of the kinetic energy correction factors
Q2// Water enters a hydraulic turbine through a 26 cm diameter pipe at a rate of 1.2 m^3/s and exits through a 21 cm diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 2 m. For a combined turbine generator efficiency of 91%. determine the net electric power output. Disregard the effect of the kinetic energy correction factors.
Water flowing steadily at a rate of 0.16 m3/s is deflected downward by an angled elbow as shown. For D = 30 cm, d = 10 cm, and h = 50 cm, determine the force acting on the flanges of the elbow and the angle its line of action makes with the horizontal. Take the internal volume of the elbow to be 0.03 m3 and disregard the weight of the elbow material and the frictional effects.
The water level in a tank is 70 ft above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank is at sea level, and the water surface is open to the atmosphere. In the line leading from the tank to the nozzle is a pump, which increases the water pressure by 15 psia. Determine the maximum height to which the water stream could rise.
The shaft power of a turbine operating with 80 percent efficiency is 450 kW. If the mass flow rate through the turbine is 625 kg/s, the load removed from the fluid by the turbine iswhat is the amount? Take it as g=9.81 m/s2
A 15-hp (shaft) pump is used to raise water to a 42-m higher elevation. If the mechanical efficiency of the pump is 82%, determine the maximum volume flow of water.
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.7 m3/s and exits through a 25-cm-diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine–generator efficiency of 83 percent, determine the net electric power output. Disregard the effect of the kinetic energy correction factors. Take the density of water to be 1000 kg/m3 and the density of mercury to be 13,560 kg/m3.
Water is flowing through a 15-cm-diameter pipe that consists of a 3-m-long vertical and 2-m-long horizontal section with a 90° elbow at the exit to force the water to be discharged downward, as shown in Fig. P6–55, in the vertical direction. Water discharges to atmospheric air at a velocity of 5 m/s, and the mass of the pipe section when filled with water is 17 kg per meter length. Determine the moment acting at the intersection of the vertical and horizontal sections of the pipe (point A). What would your answer be if the flow were discharged upward instead of downward?
A garden hose attached with a nozzle is used to fill a 40-literbucket. The inner diameter of the hose is 2.0 cm, and it reduces to1.0 cm at the nozzle exit. If it takes 58 s to fill the bucket withwater, determine (a) the volume and mass flow rate of waterthrough the hose, and (b) the mean velocity of water at the nozzleentry and exit.
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. Determine the work done per unit weight of water, in Newton-Meter per Newton.
A pump rated at 1800 W is used to transfer water from an open tank to another open tank. The surfaces of the two tanks are kept 20 m apart, vertically, while the mass flow of the water is 5 kg/s. Determine the efficiency of the pump