Consider a flat plate as shown below. Freestream air approaches parallel to the plate with the conditions shown. Assume Hair = 1.63 x 10-5 kg/m-s. Determine; a) the overall drag per unit depth (N/m) for the laminar flow case, b) the overall drag per unit depth (N/m) for the turbulent flow case, and M₁ = 0.4 alt. = 5,000 m L = 0.75 m mm

Consider a flat plate as shown below. Freestream air approaches parallel to the plate with the conditions shown. Assume Hair = 1.63 x 10-5 kg/m-s. Determine; a) the overall drag per unit depth (N/m) for the laminar flow case, b) the overall drag per unit depth (N/m) for the turbulent flow case, and M₁ = 0.4 alt. = 5,000 m L = 0.75 m mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air at 20°C and 1 atm flows at 3 m/s past a sharp flat plate2 m wide and 1 m long. (a) What is the wall shear stress atthe end of the plate? (b) What is the air velocity at a point4.5 mm normal to the end of the plate? (c) What is the totalfriction drag on the plate?
Based strictly on your understanding of the flat-plate theoryplus adverse and favorable pressure gradients, explainthe direction (left or right) for which airflow past theslender airfoil shape in Fig will have lower total(friction 1 pressure) drag.
Consider laminar flow past a sharp flat plate of width b andlength L. What percentage of the friction drag on the plateis carried by the rear half of the plate?
Calculate thickness of the boundary layer (in metre) under laminar flow condition when distance from the upstream edge is 2.15 metre and local Reynolds number is 3000. Write the final answer in the box below.
For flow over a smooth plate, what approximately is the maximum length of the boundary layer if V_o = 9.0 m/s in the irrational uniform flow and the fluid is air? Water?
A commercial airplane has a total mass of 150,000 lbm and a wing planform area of 1700 ft2. The plane has a cruising speed of 625 mi/h and a cruising altitude of 38,000 ft where the air density is 0.0208 lbm/ft3. The plane has double-slotted flaps for use during takeoff and landing, but it cruises with all flaps retracted. Assuming the lift and drag characteristics of the wings can be approximated by NACA 23012, determine (a) the minimum safe speed for takeoff and landing with and without extending the flaps, (b) the angle of attack to cruise steadily at the cruising altitude, and (c) the power that needs to be supplied to provide enough thrust to overcome drag. Take the air density on the ground to be 0.075 lbm/ft3.
Read the question carefully and give me right solutions with clear calculations. The air flows past a 1m diameter disk oriented normal to upstream flow at 6.8m/s. The pressure distribution on front of the disk is function of the radius, where p(r) = (25 − 100 r2 ) N/m2 , and the pressure acts uniformly on back side with suction pressure of pback = −22 P a. a. Determine the total drag force on the disk. b. Calculate the drag coefficient for the disk . (Density = 1.25 kg/m3 ).
A commercial airplane has a total mass of 70,000 kg and a wing planform area of 150 m2. The plane has a cruising speed of 558 km/h and a cruising altitude of 12,000 m, where the air density is 0.312 kg/m3. The plane has double-slotted flaps for use during takeoff and landing, but it cruises with all flaps retracted. Assuming the lift and the drag characteristics of the wings can be approximated by NACA 23012 , determine (a) the minimum safe speed for takeoff and landing with and without extending the flaps, (b) the angle of attack to cruise steadily at the cruising altitude, and (c) the power that needs to be supplied to provide enough thrust to overcome wing drag.
A liquid (? = 850 kg/?3; ? = 1.7 × 10−1 Pa ∙ s) flows tangentially past a flat plate. If the free stream velocity is 2 m/s Question 1: what is the velocity 5 m downstream from the leading edge of the plateand 15 mm away from the plate. Question 2: if that plate is 10 m long and 3 m wide. Determine the drag force on the plate when liquid flows over both sides of the plate. (just only answer Question 2)!!!
The viscous laminar flow of air over a flat plate results in the formation of a boundary layer. The boundary layer thickness at the end of the plate of length L is Delta L . When the plate length is increased to twice its original length. The percentage change in laminar boundary layer thickness at the end of the plate (with respect to Delta L ) is ______
The standard sea level value of viscosity coefficient for air is μ = 1.7894×10−5 kg/(m · s) = 3.7373 × 10−7 slug/(ft · s). The wing on a Piper Cherokee general aviation aircraft is rectangular, witha span of 9.75 m and a chord of 1.6 m. The aircraft is flying at cruisingspeed (141 mi/h) at sea level. Assume that the skin-friction drag on thewing can be approximated by the drag on a flat plate of the samedimensions. Calculate the skin-friction drag:a. If the flow were completely laminar (which is not the case in real life)b. If the flow were completely turbulent (which is more realistic)Compare the two results.
The drag of an airfoil (Fig.) increases considerably ifyou turn the sharp edge around 180° to face the stream. Canyou explain this?