FUNDAMENTALS OF CONVECTIONConsider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s.What is the minimum length of the plate necessary for the Reynolds number to reach 2x107?If the critical Reynolds number is 5x105, what type of flow regime would the airflow experience at 0.2 m from the leading edge?Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject

Answered: Image /qna-images/answer/b7d1f69d-7863-4a9b-9cb2-0de25f25d305.jpg

Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s. What is the minimum length of the plate necessary for the Reynolds number to reach 2x107?

Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s. What is the minimum length of the plate necessary for the Reynolds number to reach 2x107?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.63P

See similar textbooks

Related questions

Q: Q-2 For a beam of hollow rectangular section of outer geometry of b x d and the inner geometry of b₁…

A: Given: Area moment of inertia about its axis passing through the plane (the plane of area of cross…

Q: A water jet strikes a moving plate at velocity of 10 m/s as the plate moves at a velocity of 2 m/s.…

Q: in system the heat is supplied to generator b and the final state of stream after condensing…

Q: Link 2 of the mechanism shown rotates about the z-axis w.r.t. the ground (Link 1) at a constant…

A: Given: Rotational speed of the link 2 about z axis: →ωz=+2 rad/s (taking + sign for clockwise…

Q: aded with uniform vertical thin r case has a total weight of 1000 N of static friction 0.3 with the…

Q: What is the main reason for conducting a 3-point stroke test on the pneumatic control valves on the…

A: The correct option is A.

Q: b) For the truss in the figure below, determine the zero-force members and give a short explanation…

Q: Label the components in the pneumatic circuit

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: given; diameter of steel(d1)=0.500inallowable shear stress of steel(τs)=13ksimaximum torque…

Q: Consider the belt drive having a diameter of 150 mm that is mounted on the overhung end of a shaft,…

A: Given: The diameter of belt drive, d' = 150 mm = 0.15 m The overhang length, x = 30 mm = 0.03 m The…

Q: 2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage…

Q: The 172-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right…

A: Given:me=172 lbm=21 lba=0.28 gNOTE: According to Bartleyby's policy we shall answer only one…

Q: The torques shown are exerted on pulleys A and B. Consider TA = 270 N·m and TB = 400 N·m. Knowing…

Q: Consider axial vibration of the uniform bar in Fig. 1 Obtain the characteristic equation from which…

A: Given, m=ρAL4 a) ∆(A − λI) = 0 is called the characteristic equation of matrix A. Eigenvalues λ of A…

Q: The specific volume of superheated water vapor at 0.6 MPa and 900°C is 0.90179 m³/kg in the steam…

A: Given: T = 900 deg C P = 0.6 MPa specific volume = 0.90179 m3/kg

Q: A skier starts from rest on the 33° slope at time t = 0 and is clocked at t = 3.10 s as he passes a…

Q: 25. 50 50 C1 b C₂ >_25_1 x

A: Givensimply supported beamconcentated load at center P=300kNlength of span L=3mshear stress…

Q: The 186-lb exerciser is beginning to execute a bicep curl. When in the position shown with his right…

A: Given data WE=186 lb WC=22 lb ay=0.30g

Q: The rate of heat flow (conduction) between two points on a cylinder heated at one end is given by…

Q: in Figure 4b. A load of 200 N is applied at B at an angle 30°. The structure has diameter of 50mm,…

Q: 2. Determine the reactions at the supports A and B for the jib crane shown below. Also identify if…

Q: how did they get Fc

Q: pls answer asap!! A jet of water is projected vertically and has a velocity of 26 m/s. Neglecting…

A: The height up to which the water jet could rise is 34.5 m.

Q: Block A of 500-kg mass is subjected to a towing force F= 2000 t^2 + 3000 t N where "t" is in…

Q: A two-stage piston-cylinder system compresses propane from 7 kPa to 17 bar in a refrigeration…

A: Given: Initial pressure of the compressor→Po=7 kPa Final pressure of the compressor→Pf=17 bar=1700…

Q: Determine the distance from the upper surface of the symmetric double-T beam cross section to the…

Q: A vertical cylinder of 60 mm diameter is penetrated by another cylinder of 40 mm diamet the axis of…

A: A vertical cylinder of 60 mm diameter is penetrated by another cylinder of 40 mm diameter, Q2. the…

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

Q: a) What is a truss? Explain shortly in your own words, and illustrate with one example. b) For the…

Q: An aircraft has the following relevant specification outlined below: Weight: 329 kN Wing planform…

A: Given: The weight, W = 329 kN The planform area, A = 191 m2 The drag polar, CD = 0.01+0.064CL2 The…

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

Q: A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The…

Q: Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm…

A: What does mean by Cavitation: Cavitation is a low-pressure phenomenon. When the pressure of a…

Q: Draw isometric projection of casting, two views (FV and TV) of which are shown in figure in First…

A: Refer the following image for the the required rough sketch of isometric view of the given…

Q: QUESTION 35 Determine location (coordinate) of the centroid of the composite body shown. (X=0.954 m,…

Q: H.W.9 The two bars shown in Figure P2.2 are used to support load P. When unloaded, joint B has…

Q: Find the strain energy of a steel rod, of diameter 20 mm and length 400 mm, when it is subjected to…

A: Given:d=20 mmlength, l=400 mmP=40 KNE=200 GPa

Q: A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown…

Q: Calculate the y-coordinate of the centroid of the shaded area. 56 mm Answer: y = 25-25 mm mm 25 mm…

Q: In a Parson reaction turbine, the angles of receiving tips are 35º and of discharging tips 20º. The…

A: Blade speed , u = 125 m/s take a scale 5 cm = 125 m/s 1 cm = 25 m/s from the velocity triangle:…

Q: Is truss stable or not

A: Given data : Number of member m=5 Number of joint J=4 Number of external support reaction R=2+1=3…

Q: 41.) A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

Q: The particle of mass m = 2.1 kg is attached to the light rigid rod of length L = 0.91 m, and the…

Q: -rmation matrix T is give 50 ас0 =c0 as0 K d 1 ng concepts of rigid bod

A: solution is below in step 2.

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

Q: The apparatus shown below was created by attaching a 12 kg sphere to end of a 4 kg uniform rod. If…

Q: bulb temperature (DBT

Q: Illustrate the correct sequence of the Theory of Accidents by Heinrich? A. B. C. D. Social…

A: Heinrich's Domino Theory states that accidents result from a chain of sequential events,…

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

Q: Determine the a very small c sk A: located co- above the smalle ick may bo tako

A: solution of above problem is below:

Question

FUNDAMENTALS OF CONVECTION

Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s.

What is the minimum length of the plate necessary for the Reynolds number to reach 2x10⁷?

If the critical Reynolds number is 5x10⁵, what type of flow regime would the airflow experience at 0.2 m from the leading edge?

Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
5.43 A refrigeration truck is traveling at 130 km/h on a desert highway where the air temperature is . The body of the truck is idealized as a rectangular box 3 m wide, 2.1 m high, and 6 m long, at a surface temperature . Assume that (1) the heat transfer from the front and back of the truck is neglected, (2) the stream does not separate from the surface, and (3) the boundary layer is turbulent over the whole surface. Calculate the required cooling rate of the refrigeration unit.
Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? I need the solution from fundamental concepts of how the heat flow behaves in the system
A steel plate has dimensions of 3 m by 1 m and is initially kept at a temperature of 30 degree Celsius. It is cooled by blowing air parallel to the 1 m edge at 9 km/hr. The temperature of the flowing air is maintained at 10 degree Celsius. Estimate the convection heat transfer rate from both sides of the plate.
Air at 1 atm is flowing at a velocity of 1.5 m/s across a flat plate. The film temperature between the plate and the air is 500 K. What is the Stanton number at this condition if the convection coefficient is 44.9 W/m² K?
Experiment No. (5) Heat Transfer, Power Input and Surface temperature Questions and Discussions 1. What is the difference between natural and forced convection heat transfer? 2. What sources of error are there in this experiment? 3. Mention the parameters you utilized during the calculation and discuss them briefly. 4. In what functions does Nusselt number in natural convection differ from forced convection, Discuss. 5. Give two examples of natural convection heat transfer. 6. In natural convetion, what makes the hot part of fluid to move?
1.0 Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with velocity of 1 m/s: atmospheric air, water, engine oil, and mercury. For each fluid, determine the velocity and thermal boundary layer thicknesses, in mm, at a distance of 20 mm from the leading edge.
A flat aluminum plate 8 m long and 1.5 m wide has a surface temperature of 180°C. For its cooling, air at 1 atm and speed of 10 m/s circulates at 20°C parallel to the length of the plate. a) Determine a steady state of convection heat transfer rate. b) The fins are 50 mm long and 0.5 mm thick and the occupancy density is 75 fins per unit length of the plate. The conve coefficient of the air over the plate resulting from the placement of fins is 10 W/m2.K. Determine a calorie transfer rate and percentage increase from part (a).