A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B O 105.9 MPa O 120.7 MPa O 113.9 MPa O 94.0 MPa 89.4 MPa L

A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B O 105.9 MPa O 120.7 MPa O 113.9 MPa O 94.0 MPa 89.4 MPa L

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the maximum normal stress, MPa, due to bending on section C? For S200x27.4, S = 235µm^3. Answer in whole numbers, no units. (Example: 123MPa --> 123)
Determine the maximum shear stress acting at a tubular cross-section having an outer diameter D, = 100 mm and inner diameter D; = 80 mm, if the applied torque T = 500 N.m. Take ) = 5.79624 x 108 m?; Select one: O 431MPa O 2.15MPa O 6.15MPa O 1032MPa O 8.62MPa
Calculate maximum compressive strain on circular beam with an outside diameter of 80mm and wall thickness of 12mm when it is loaded in bending as shown in Figure Q10. (E=65 GPa)a) 5158 micro-strain b) 355.45micro-strain c) 17127 micro-strain d) 62271micro-strain
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590
The connecting rod of a four stroke cycle Diesel engineis of circular section and of length 550 mm. The diameter and stroke of the cylinder are 150 mm and240 mm respectively. The maximum combustion pressure is 4.7 N/mm2. Determine the diameter ofthe rod to be used, for a factor of safety of 3 with a material having a yield point of 330 MPa.Find also the maximum bending stress in the connecting rod due to whipping action if the engine runsat 1000 r.p.m. The specific weight of the material is 7800 kg/m3. [Ans. 33.2 mm ; 48 MPa]
Ten bolts of 10 mm diameter are used to connect two shafts as shown. If the mean diameter of the circle is d = 200 mm, and the failure shear stress of the bolt’s material is 70 MPa, determine the maximum permissible torque (N.m). Take F.S. = 1.05. (Input the answer with two decimal places; like 263.46, 3682.42, ....).
An aluminum tube with the cross section shown has a constant wall thickness of 2 mm. A torque T = 400 N·m is applied to the tube. Use G= 28 GPa What is the area of the tube? a. 957.08mm2 b. 968.09mm2 c. 966.08mm2 d. 977.08mm2 What is the total length of the median line? a. 0.1313m b. 0.1314m c. 0.1315m d. 0.1316m What will be the result shear flow of the object? a. 207,967.94 N/m b. 208,968.98 N/m c. 209,978.96 N/m d. 209,979.00 N/m The shearing stress value will be? a. 104.5 MPa b. 105.6 MPa c. 104.6 MPa d. 105.7 MPa The angle of twist result is? a. 14.68 Deg/m b. 12.66 Deg/m c. 14.68 Deg/m d. None of the above.
Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 N - m . Determine the average shear stress developed at point A. The tube is fixed at the other end. a) 1.75 MPa b) -1.65 MPa c) 4.086 MPa d) 2.095 MPa
The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 0.02R mm and an outer diameter of 0.444R mm. When the vessel is pressurized to 0.004R MPa, determine the change in the overall length of the vessel. Use E = 200 GPa and µ = 0.3 for steel. Neglect localized bending. Note R=993
If Poisson's ratio of a material is 0.5, then the elastic modulus for the material is a)three times its shear modulus b)four times its shear modulus c)equal to its shear modulus d)indeterminate
The anchor from Part A can also fail in shear in the circular head, as shown (Figure 3). What is the minimum thickness t required for the head to support the allowed load Pallow = 11 kNkN if the material fails in shear at τfail = 30 MPa ? Use a factor of safety F.S. = 2.2. d= 1.93 cm h= 2.9 cm
Calculate the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 150 mm and consisting of 24 turns of 10-mm diameter wire when the spring is stretched 180mm. Use A.M. Wahl's formula and G=42 GPa. Group of answer choices 24.336 MPa 36.689 MPa 48.778 MPa 12.233 MPa