Consider a gas turbine cycle with two stages of compression and two stages of expansion. The pressure ratio across each compressor stage and each turbine stage is 8 to 1. The pressure at the entrance of the first compressor is 100 kPa, the temperature entering each compressor is 20°C, and the temperature entering each turbine is 1100°C. A regenerator is also incorporated into the cycle and it has an effectiveness of 70%. Determine the compressor work, the turbine work, and the thermal efficiency of the cycle

Consider a gas turbine cycle with two stages of compression and two stages of expansion. The pressure ratio across each compressor stage and each turbine stage is 8 to 1. The pressure at the entrance of the first compressor is 100 kPa, the temperature entering each compressor is 20°C, and the temperature entering each turbine is 1100°C. A regenerator is also incorporated into the cycle and it has an effectiveness of 70%. Determine the compressor work, the turbine work, and the thermal efficiency of the cycle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air enters the compressor of a regenerative gasturbine engine at 310 K and 100 kPa, where it is compressed to 900 kPa and 650 K. The regenerator has an effectiveness of 80 percent, and the air enters the turbine at 1400 K. For a turbine efficiency of 90 percent, determine the thermal efficiency. Assume variable specific heats for air.
A gas turbine cycle with a stage of reheat and regeneration operates under the conditions given below, as illustrated in the figure. The turbine efficiencies are 86%, and the compressor efficiency is 81%. Furthermore, the work output of the high-pressure turbine is just enough to drive the compressor. Determine the pressure at which the reheater operates. T1 = 1300 K, T6 = 3000 K, P1 = 450 kPa, P6 = 100 kPa
In an air standard gas turbine cycle, air at 14.5 psia and 70 F is first compressed to 80 psia in a compressor of 82 percent efficiency. The hot air leaving the combustion chamber at 1250 F is expanded back to 14.5 psia in a turbine of 85 percent efficiency. If a regenerator is inserted into the cycle to heat the air leaving the compressor to 650 F, determine the thermal efficiency of the cycle and the effectiveness of the regenerator.
Air enters the compressor of a gas turbine at 100 kPa and 25°C. Determine the back work rate and thermal efficiency of the Brayton cycle for a pressure ratio of 5 and a maximum temperature of 850°C.
The 7FA gas turbine manufactured by General Electric is reported to have an efficiency of 35.9 percent in the simple-cycle mode and to produce 159 MW of net power. The pressure ratio is 14.7 and the turbine inlet temperature is 1288°C. The mass flow rate through the turbine is 1,536,000 kg/h. Taking the ambient conditions to be 20°C and 100 kPa, determine: (a) the isentropic efficiency of the turbine and the compressor, (b) the thermal efficiency of this gas turbine if a regenerator with an effectiveness of 80 percent is added. Answers: (a) 0.849, 0.924 (b) 0.496
A gas-turbine power plant operating on an ideal Brayton cycle has a pressure ratio (P2/P1= P3/P4) of 10. The air temperature is 27 ºC at the compressor inlet and 1365 K at the turbine inlet. Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine, (b) the specific work, and (c) the thermal efficiency.
Air is used as the working fluid in a simple ideal Brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300 K, and a turbine inlet temperature of 1000 K. Determine the required mass flow rate of air for a net power output of 70 MW, assuming both the compressor and the turbine have an isentropic efficiency of 85 percent. Assume constant specific heats at room temperature.
Consider an ideal gas-turbine cycle with two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor and turbine is 3. The air enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. Determine the back work ratio and the thermal efficiency of the cycle, assuming no regenerator is used.
A simple Rankine cycle has a pump with an isentropic efficiency of 70%. The inlet and outlet pressures of the turbine are 6 MPa and 0.075 MPa, respectively, and steam enters the turbine at 550°C. Determine a) the isentropic efficiency of the turbine if the quality at the turbine outlet is to be ? = 1, b) the thermal efficiency of the cycle, c) the rate of heat input into the boiler if the net power output of the cycle is 10 MW.
Air is used as the working fluid in a simple ideal Brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300 K, and a turbine inlet temperature of 1000 K. Determine the required mass flow rate of air for a net power output of 70 MW, assuming both the compressor and the turbine have an isentropic efficiency of 100 percent.
For a specified pressure ratio, why does multistage compression with intercooling decrease the compressor work, and multistage expansion with reheating increase the turbine work?
A Brayton cycle with a pressure ratio of 15 operates with air entering the compressor at 70 kPa and 0°C, and the turbine at 600°C. Calculate the net specific work produced by this cycle treating the air as an ideal gas with constant specific heats.