Consider a load that has an impedance given by Z=100-j50 Ω. The current flowing through this load is I= 152 ∠30° A. Is the load inductive or capacitive? Determine the power factor, power, reactive power, and apparent power delivered to the load.

Consider a load that has an impedance given by Z=100-j50 Ω. The current flowing through this load is I= 152 ∠30° A. Is the load inductive or capacitive? Determine the power factor, power, reactive power, and apparent power delivered to the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17P: Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a)...

See similar textbooks

Related questions

Q: Determine if a load (impedance) is capacitive or inductive, given the following 4 cases: a. pf =…

A: Given: Consider the following cases: a. pf = 0.87, leadingb. pf = 0.42, leadingc. v(t) = 42 cos(ωt)…

Q: The voltage across a load is v(t)=1042 cos(ωt+10°) V, and the current through the load is i(t) = 202…

A: Given: voltage across the load is, v(t)= 1042cos(ωt+10°) V Voltage across the load…

Q: The circuit with 3 parallel loads is explained as follows. Load1 = draws 8 kW average power and the…

Q: For the circuit shown, a) Determine the load impedance that will result in maximum average power…

A: Maximum power theorem: This states that in the circuit load resistance is equal to the source…

Q: For the circuit shown, what is the complex power, S, consumed by the load impedance? (Assume the…

A: The complex power is given by: S=VI*where,I* is conjugate of current I. Given: Vs=150∠0°R=15ΩC=150…

Q: Perform phasor analysis to the circuit shown to evaluate the total complex power (S) absorbed by the…

A: In this question, we need to determine the across the load 40+30j i. average power (P), ii. reactive…

Q: Q 1) Given that Z1 = 302(-40°) N and Z2 = 50215° N, find the (a) apparent power, (b) real po (c)…

Q: 111.803 L- 41.57° V. (i) Determine the value of impedance Za. UTM UTMD Determine the complex power,…

Q: A load consisting of a 1.35 kO resistor in parallel with a 405 mH inductor is connected across the…

A: In this question, We need to determine the average active power, reactive power ,apparent power and…

Q: For the circuit shown, ZL = 21 – j45 2. What component is needed to form impedance ZpFc in parallel…

Q: j2 Ω m =jXΩ HH ΚΩ ww 40/0° V ZL 5Ω For the circuit shown above, what is the magnitude of the load…

A: In this question, We need to determine the impedance ZL for the maximum power transfer to the load…

Q: If a current of I = 30 cos(1000t + 60°) mA was found to be flowing through an impedance found…

A: according to the ohm's law if the impedance is Z and current i I then value of the votlage is given…

Q: Three branches having impedances of 3+j4 Ω, 16−j12 Ω, and−j4 Ω, respectively, are connected in…

A: Given data: Impedance Z1 = 3+j4 Ω Impedance Z2 = 16-j12 Ω Impedance Z3 = -j4 Ω The admittance of the…

Q: (a) A load has impedance, Z = (50 + j14) N. Convert this value of Z into polar form, |Z|40, where Z…

Q: A impedance of Z = 20236.87° N is connected across a source with a voltage of 141.421 sin (314.159t)…

A: Given ImpedanceZ=20∠36.87° ΩVoltage V=141.421sin314.159t v

Q: 2. In the simple system below, draw the V-Q curve for the load bus if P-D0. What is the maximum…

A: As per the guidelines given, We can only provide the solution of the first question in multiple type…

Q: 3. In the circuit given below the load impedance Z, is adjusted for maximum average power transfer…

Q: 19.22 72mH V, Z V, -

A: we need to find out phasor V1 . Given:: the load is connected to 100V (rms) and dissipates 1kW at…

Q: Find the following in rectangular form: a. What is the real power delivered by the source (in W)? b.…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: 2. For the circuit below with source voltage phasor given in Pms, a. Find phasors Is, 12, V1, and V2…

A: (a) For current in source side of the transformer circuit given is calculated as

Q: The load impedance in the circuit shown is shunted by a capacitor having a capacitive reac- tance of…

A: In Network Phasor load current and voltage Real and imaginary power across load , transmission…

Q: The circuit below is operating in ac steady-state. The source voltage is Vz = 25/2 sin (4000t) v.…

Q: For the circuit shown, ZL 21 – j45 N . What component is needed to form impedance ZpFc in parallel…

A: Given circuit: ZL=21-j45 Ω

Q: For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZL and ZL…

Q: For a circuit with the below rms voltage source and impedance: V1 = 115 20° V Z = 65 – j 23…

Q: For a given load, Vms=110Z85°V, Ims=0.4Z15°A. Determine: a) the complex and apparent powers b) the…

A: Solution: V Given : Vrms = 110 < 85° V Irms = 0.4 < 15° A Z= V / I Z= Impedance…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

Q: Exercise#2: We have a load with an impedance given by Z = 30+j 40 Q. The voltage across this load is…

Q: We have a load with an impedance given by Z= 30+j40 Ω.The voltage across this load is V = 15002 ∠30°…

A: Given data, The value of impedance is Z = 30+j40 Ω. The voltage across the load is V = 15002 ∠30°V.…

Q: An electric load consists of a resistor, a capacitór and an inductor connected in series. The total…

A: Introduction: R-L-C circuit: RLC circuit consists of passive parameters like resistance (R),…

Q: An impedance ZL = (11.5 + j10) ohms is connected in parallel with an impedance ZC = (8 – j20) ohms.…

Q: (d) The branch current (in both polar and Cartesian forms): I= (e) The branch current (in both polar…

Q: 3. In the circuit given below the load impedance Z is adjusted for maximum average power transfer to…

Q: For the circuit shown below, find the phasor current I, the real power, reactive power and apparent…

A: The RC circuit is shown below: The current I is the sum of the current through the resistor and…

Q: In the circuit below Z1 = 40/-60° and Z2 60 40° n. Calculate: a) The currents 11, l2 and I, b) The…

A: Note: As per our policy, I have attempted the first three subquestions. Given data: Z1=40∠-60o…

Q: 14. Consider this power distribution system to a customer: Transmission line current Power company V…

A: The solution is given below

Q: 1 In the circuit of Figure. Z, = 60Z– 30°N · and· Z, = 40Z45°Q. %3D (1)-Find the phasors İ,,İ‚‚İ¸.…

A: Given circuit,

Q: For the system shown, (a) find the average/real power Pg and reactive power Qs supplied by the…

A: Given system has parameters as: Load 1- Q1=100VAR, P1=200W, Load 2- Q2=100VAR, P2=200W, Load 3-…

Q: Use the phasor analysis method to solve for the AC steady-state mesh currents, and then express each…

Q: For the following voltage and current phasors, calculate the complex power, apparent power, real…

Q: For the circuit shown, Z parallel with Z, such that the load achieves unity power factor? = 50 – j30…

Q: mm 50 2 10mH V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of the…

Q: Consider the network as shown in figure Q1. Determine the load impedance ZL for maximum average…

A: We will use thevenine theorem to find load impedance and maximum power transfer to load.

Q: Find the complex power supplied by the source and the power factor of the source for the network…

Q: Can anyone help? This is an old exam and is answered (wrong might I add) and I need help.

A: For the circuit to achieve unity power factor, it must be at resonant.From the circuit,

Q: shown below, de following: a) The impedance Zi that results in maximum average power transferred to…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 1.2 Two circuits, the impedances of which are given by Z = 10 + j15 2 and %3D Z, = 6 - j8 2 are…

A: According to question we have to calculate the value of power taken by each branch.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
We have a load with an impedance given by Z= 30+j40 Ω.The voltage across this load is V = 15002 ∠30° V.Is the load inductive or capacitive? Determine the power factor, power, reactive power, and apparent power delivered to the load.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
The load impedance ZL for the circuit shown is adjusted until maximum average power is delivered to ZL.1. a) Find the maximum average power delivered to ZL.2. b) What percentage of the total power developed in the circuit isdelivered to ZL?
For the following voltage and current phasors, calculate the complex power, apparent power, real power, and reactive power. Specify whether the pf is leading or lagging. a. ? = 220∠30° ? ???, ? = 0.5∠60° ? ??? b. ? = 160∠45° ? ???, ? = 8.5∠90°? ???
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
Understand ac power concepts, their relationships to one another, and how to calculate them in a circuitA load consisting of a 1.35 kΩ resistor in parallel with a 405 mH inductor is connected across the terminals of a sinusoidal voltage source vg, where vg = 90 cos 2500t V. Find 1. a) the average power delivered to the load,2. b) the reactive power for the load,3. c) the apparent power for the load, and4. d) the power factor of the load.
Find the complex power for the following: Vrms= 200 ∠ 30∘ V, Z= 40+ j60 Ω in addition form
The impedance ZL in the circuit is adjusted for maximum average power transfer to ZL. The internal impedance of the sinusoidal voltage source is 4+j7 Ω. 1. a) What is the maximum average power delivered to ZL?2. b) What percentage of the average power delivered to the lineartransformer is delivered to ZL?
Calculate ZL for maximum average power transfer in the circuit, and find the maximum average power delivered to the load. The given answer is ZL=2-j2 Ω, PL=45 W
The circuit with 3 parallel loads is explained as follows. Load1 = draws 8 kW average power and the lagging power factor is 0.8. Load2 = draws 2.20 kVA and forward power factor is 0.6. Load3 is an impedance of Z3 = 2.5 + j5.0 Ohms. If the source frequency is 60 Hz, derive the SS equation for VS (t).