The voltage across a load is v(t)=1042 cos(ωt+10°) V, and the current through the load is i(t) = 202 cos(ωt-20°) A.The reference direction for the current points into the positive reference for the voltage. Determine the power factor, the power, the reactive power, and the apparent power for the load. Is this load inductive or capacitive?

The voltage across a load is v(t)=1042 cos(ωt+10°) V, and the current through the load is i(t) = 202 cos(ωt-20°) A.The reference direction for the current points into the positive reference for the voltage. Determine the power factor, the power, the reactive power, and the apparent power for the load. Is this load inductive or capacitive?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.11MCQ: The power factor for an inductive circuit (R-L load), in which the current lags the voltage, is said...

See similar textbooks

Similar questions

The power factor for an inductive circuit (R-L load), in which the current lags the voltage, is said to be (a) Lagging (b) Leading (c) Zero
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
Understand ac power concepts, their relationships to one another, and how to calculate them in a circuitA load consisting of a 1.35 kΩ resistor in parallel with a 405 mH inductor is connected across the terminals of a sinusoidal voltage source vg, where vg = 90 cos 2500t V. Find 1. a) the average power delivered to the load,2. b) the reactive power for the load,3. c) the apparent power for the load, and4. d) the power factor of the load.
Perform phasor analysis to the circuit shown to evaluate the total complex power (S) absorbed by the (40 + j30) Ω load. Afterwards, identify the following for the (40 + j30) Ω load: i. average power (P), ii. reactive power (Q), iii. apparent power (S), iv. power factor (pf) and predict whether the power factor is leading or lagging
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
1. Solve for the equivalent impedance and admittance seen at the source. Solve for is(t). 2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
A Y-connected balanced three-phase source is feeding a balanced three-phase load. The voltage and current of the source coil are: Calculate the following: The rms phase voltage. The rms line-to-line voltage. The rms current in the source. The rms current in the transmission line. The frequency of the supply. The power factor at the source side, state leading or lagging. The three-phase real power delivered to the load. The three-phase reactive power delivered to the load. If the load is connected in delta configuration, calculate the load impedance.
For the following voltage and current phasors, calculate the complex power, apparent power, real power, and reactive power. Specify whether the pf is leading or lagging. a. ? = 220∠30° ? ???, ? = 0.5∠60° ? ??? b. ? = 160∠45° ? ???, ? = 8.5∠90°? ???
The voltage at the terminals of a load is 250 V(rms). The load isabsorbing an average power of 40 kW and delivering a magnetizingreactive power of 30 kVAR. Derive two equivalent impedance modelsof the load.