) Consider a mass (m-5 kg) connected to a massless rod of length (L=2 m) to swing about point O, as shown in Figure (2). The mass is also connected to a spring of spring constant (k=10 N/m). The other end of the spring is connected to a pivot. The unstretched length of the spring is 1 m. Find the equation of motion of the L-2 m system. m-5 kg 3 m k-10 N/m Figure 2

) Consider a mass (m-5 kg) connected to a massless rod of length (L=2 m) to swing about point O, as shown in Figure (2). The mass is also connected to a spring of spring constant (k=10 N/m). The other end of the spring is connected to a pivot. The unstretched length of the spring is 1 m. Find the equation of motion of the L-2 m system. m-5 kg 3 m k-10 N/m Figure 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft in the figure, carrying three unbalanced masses, is rotating at a constant speed hızla = 10 r / s. Find the balancing values (kg.mm) and their positions in case of balancing in DI and DII planes.
A disk is attached by a spring to a pin. The disk can roll in the horizontal direction and the pin is above it. The spring has an unstretched length of .5m and a spring modulus of 600 N/m THe disk has a mass of 20kg and a radius of 200mm The center of hte disk is 600mm below the pin and 320mm to the side (so the spring starts diagonal) If the spring is released, what is the speed of the disk when the spring is perfectly vertical? Assume the disk does not slip and is free to spin
A counterweight of mass m= 4.10 kg is attached to a light cord that is wound around a pulley as shown in the figure below. The pulley is a thin hoop of radius R = 6.00 cm and mass M = 2.30 kg. The spokes have negligible mass. What is the net torque on the system about the axle of the pulley? When the counterweight has a speed v, the pulley has an angular speed ? = v/R. Determine the magnitude of the total angular momentum of the system about the axle of the pulley. Using your result from (b) and τ = (dL) / (dt), calculate the acceleration of the counterweight. (Enter the magnitude of the acceleration.)
A beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables available in the palette. e. Enter an expression for the vertical component of…
- A double-pulley system, as in the right figure above, has masses m1 = 2.00 kg, m2 = 1.20 kg, and m3 = 0.800 kg. (a) What are the accelerations of all the masses? (b) What are the tensions in all the ropes
An engine flywheel has a mass of 6.5 tones and the radius of gyration is 2 m. If the maximum and minimum speeds are 120 r. p. m. and 118 r. p. m. respectively, find maximum fluctuation of energy.
The beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. What is the magnitude, in newtons, of the tension in the cable? e. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables…
The uniform bar shown has mass m, length l, and mass momentof inertia I about its mass center. The bar is supported by two springs k1and k2, as shown in the figure. Obtain the differential equation of motion anddetermine the natural frequency of the system in the case of small oscillations. (USE VIRTUAL WORK METHOD)
A homogeneous slender bar AB of mass m and length L is released from rest in the position shown in figure below. Assuming that the horizontal plane is frictionless. 1.) Draw the free body diagram and say how many forces act on the bar and which force is doing the work. 2.)Draw the kinematic diagram and show how manoy vectors act on the bar. 3.) Draw the kinetic diagram and show how many inertia-term vectors act on the bar.
From the following diagram find with k1=20N/m, k2=30 N/m, k3=25 N/m, k4=35 N/m, k5=50N/m and k6=60N/m, m=10kg A) the equivalent spring B) the displacement C) the work performed
A disk is attached by a spring to a pin. The disk can roll in the horizontal direction and the pin is above it. The spring has an unstretched length of 0.5 m and a spring modulus of 600 N/m. The disk has a mass of 20 kg and a radius of 200 mm. The center of the desk is 600 mm below the pin and 320 mm to the side (So the spring starts diagonal). If the spring is released, WHAT IS THE SPEED OF THE DISK WHEN THE SPRING IS PERFECTLY VERTICAL? Assume the disk does NOT slip and is free to spin.
Consider an electrical motor with mass M= 29 kg located at the tip of a rigid beam pivoted at point A, with the other end supported by a spring and damper with stiffness, k = 6 MN/m and damper c= 12 kNs/m, as shown in the figure below. Assume that the rigid beam is massless, the length is L= 1.3 m (horizontal distance between point O and pivot point A), and zero initial conditions. If there is an unbalanced mass of m0=2 kg in the rotating part of the motor, eccentricity is e =382 mm, and the rotor is rotating with a speed of w (omega) = 203 rad/s, determine the maximum amplitude response of point O at steady state condition in millimetre. Assume the line of actions of forces created by spring and damper act through point O, the centre of electric motor. Treat the electric motor mass as a point mass for calculating its moment of inertia about point A.