Consider a metal cube with X mm long edges lying on a flat surface. A load of Y N is applied on the top surface of the cube. What is the magnitude of stress in the cube, in the direction of loading (in MPa)? X =1 Y = 10 O a. 9.00 O b. 10.00 O c. 11.00 O d. 12.00 O e. 13.00

Consider a metal cube with X mm long edges lying on a flat surface. A load of Y N is applied on the top surface of the cube. What is the magnitude of stress in the cube, in the direction of loading (in MPa)? X =1 Y = 10 O a. 9.00 O b. 10.00 O c. 11.00 O d. 12.00 O e. 13.00

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 40-kN axial load is applied to a short wooden post that is supported by a concrete footing resting…

A: (a) Write the formula for the maximum bearing stress on the concrete footing. Here, is the maximum…

Q: 02.The rigid bar ABC shown in Fig.(1) is hinged at A and supported by a steel rod at B. Determine…

Q: A 5.3-m-long steel rod must not stretch more than 2.71 mm and the normal stress must not exceed 181…

A: GivenL=5.3m∆lim=2.71mmσallow=181MPaE=193.3 GPa=193.3×103 N/mm2P=9.99 KN

Q: A rod composed of an aluminum section rigidly attached between steel and bronze section. Axial loads…

A: Given data as per the question P=3000 lb Area of rod =0.5 in2

Q: Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at…

Q: Question- 1) Two gage marks are placed exactly 270 mm apart on a 10-mm-diameter aluminum rod with E…

A: Given data: - The distance between gage is L' = 270 mm. The distance between gage after a load is…

Q: A horizontal load P is applied as shown to a short section of an S10 * 25.4 rolled-steel member.…

A: Given Maximum compressive stress = 12 ksi To find Allowable magnitude of force P

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

Q: 1. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 lb.…

A: Given: P = 400 lb d = 100 mm stress = 12 MN/m2

Q: (12) A square steel bearing plate lies between a wooden post and a concrete footing as shown.…

A: Given Stress in wood = 12.5 MPa Stress in concrete = 4.5 MPa Find Maximum value of the load, P

Q: Determine how many 11mm bolts should be used to attach a cap to a cylindrical tank with a diameter…

Q: PROBLEM 1.3 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.…

Q: For the clevis connection shown, the shear stress in the 0.212-in-diameter bolt must be limited to…

Q: Problem 3) Determine the thickness of a 120 mm wide uniform plate for safe continuous operation if…

Q: A 1∕2-in.-diameter round steel rod 40 ft long supports a load of 4 kips. How much will it elongate?…

A: Given data: The diameter of steel rod, d = 1/2 in. Length of rod, L = 40 ft. Load, P = 4 kips.…

Q: A hollow steel tube with an inside diameter of 100mm must carry a tensile load of 400 kN. Determine…

A: We have to determine hollow steel diameter

Q: DCB LCB F LAB DAB P.

Q: Three steel rods (E=200 GPa) support a 36-kN load P. Each of the rods AB and CD has a 200-mm²…

Q: Link BID consists of a single bar 30 mm wide and 12 mm thick. Knowing than each pin has : 10 mm…

A: When any external force acts on the body, the body deforms and this deformation is resisted by the…

Q: The bar shown below is tested in universal testing machine. It is observed that at a load of 40 kN…

A: Given, P=40 kN=40×103 N L1=150 mmL2=250 mmL3=150 mm d1=25 mmd2=20 mmd3=25 mm The total extension of…

Q: For the clevis connection shown, the shear stress in the 0.577-in-diameter bolt must be limited to…

Q: Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a…

Q: he stress induced in a body, when suddenly loaded, is _________ the stress induced when the same…

A: Given:The stress induced in a body, when suddenly loaded, is _________ the stress induced,when the…

Q: 3. An eccentric load is applied at a point 22 mm from the geometric axis of a 60 mm diameter rod…

A: Given Stress = 200 MPa Young's modulus, E = 200 GPa Diameter, d =…

Q: H.W: The two vertical rods attached to the light rigid bar are identical except for length. Before…

Q: A metal block of cross-section area A and length L is subject to a tensile stress of S. The block…

Q: A timber block 250 mm square is reinforced on each side by a steel plate 250 mm wide and t mm thick.…

A: GIVEN DATA- TIMBER OF 250mm SQUARE SECTION LOAD =1200KN E FOR STEEL =200GPa E FOR TIMBER =10GPa…

Q: tensile load of 8 kN is applied to a 1.6 mm long aluminum rod. The rod have stretched to a total of…

A: Stress: Stress is nothing but the force per unit area. It is represented by σ.& SI unit of…

Q: Two gage marks are placed exactly 250 mm apart on a 12-mm-diameter aluminum rod with E5 73 GPa and…

A: Given: The initial distance between the gage marks is l=250 mm. The final distance between the gage…

Q: Determine how many 17mm bolts should be used to attach a cap to a cylindrical tank with a diameter…

Q: An aluminum rod to be used in an aircraft control system is 600 lb 600 lb required to stretch 0.12…

A: Given data as per question Tensile load =600 lbAllowable stress =17 ksiYoung's Modulus =10.2×103…

Q: 1. A rod is composed of an aluminum section ngidly attached between steel and bronze setions, as…

A: Given Data: The magnitude of load, P=3000 lb

Q: Two gage marks are placed exactly 250mm apart on a 12mm-diameter aluminum rod with E=73Gpa and an…

Q: An aluminum plate (E= 74 GPa, ν= 0.33) is subjected to a centric axial load that causes a normal…

A: After the deformation, the slope is calculated by the following expression:…

Q: Two fork end pieces are to be joined together by a single steel pin of 25mm diameter and they are…

Q: Member (1) has an area of 2700 mm? and an allowable normal stress of 130 MPa. Member (2) has an area…

Q: Consider a deformable homogenous slender rod of constant area along its length. It is axially loaded…

Q: Determine how many 14mm bolts should be used to attach a cap to a cylindrical tank with a diameter…

Q: The two vertical rods attached to the light rigid bar are identical except for length. Before the…

Q: If a 50 kN load is applied on steel rod of cross-section area 400 mm?, the normal stress will be…

Q: 3. A cast-iron tube is used to support a compressive load, knowing that the maximum allowable change…

Q: A hollow circular short column of outside diameter 300 mm and thickness 10 mm carries a load of 1000…

Q: 02. A 300-mm square steel bearing plate lies between an 200-mm diameter wooden post and a concrete…

A: The cross-section area of the wooden post is written as, Aw=π4dw2=π4200 mm×1 m1000 mm2=31.42×10-3…

Q: 1.18 A load P is applied to a stecl rod supported as shown by an aluminum plate into which a…

A: Given data

Q: A compressive member of a structure is of 25 mm square cross-section and carries a load of 50 kN.…

A: When stress developed on any one of the mutual perpendicular planes passing through that point is…

Q: 11.10 (A/B). A load of 2 kN falls through 25 mm on to a stopat the end of a vertical bar 4 m long,…

Q: The aluminum rod ABC (E =10.1* 106 psi), which consists of two cylindrical portions AB and BC, is to…

A: Given:EABC,Elastic modulus of rod ABC=10.1×106 psiEDE=29×106 psiLoad,P=28 kipsNow,Deformation in…

Q: 12. A% in. -diameter rod made of the same material as rods AC and AD in the truss shown was tested…

Q: A 5.49-m-long steel rod must not stretch more than 2.45 mm and the normal stress must not exceed 189…

Q: Determine the largest load P (in KN) that can be applied to the rod if a factor of safety of 2.5…

A: load applied on rod =25kN ultimate tensile strength of pin material =100 MPa Ultimate tensile…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Consider a metal cube with X mm long edges lying on a flat surface. A load of YN is applied on the top surface of the cube. What is the magnitude of stress in the cube, in the direction of loading
(in MPa)?
X = 1
Y = 10
О a. 9.00
O b. 10.00
О с. 11.00
O d. 12.00
О е. 13.00

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.
The stress produced by a suddenly applied load as compared to that produced by the same load when applied gradually is: A. 1.5 times B. 2 times C. 3 times D. 4 times
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.002L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of 2L, determine the elongation of the block.
A seamless cylinder of storage capacity of 0.03m3 is subjected to an internal pressure of 21 MPa. The allowable stress in the material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.8mm A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder.540mm
Before loading the plate, mark a line with the inclination shown. After the load is applied, the slope of the line decreases by 5x10^-3 rad. Determine the normal stress ?. Consider E = 2.1x106 kgf/cm^2 and v = 0.30. Express your answer in units of kgf/cm^2.
For the case of plane stress, show that Hooke’s law can be written as
A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 2.1 mm. Determine the magnitude of the load required to produce a 0.002 mm change in diameter if the deformation is entirely elastic. Answer in N. The modulus of elasticity of copper is 110 GPa and it's Poisson's Ratio is 0.34. Round your answer to 0 decimal places.
Determine the safe wall thickness of a 50 inches steel tank with internal pressure of 8 Mpa. The ultimate stress is 296 Mpa. The factor of safety to use is 3. A. 2 in B. 3 in C. 5 in D. 4 in
A steel wire is 6 m long, hanging vertically supports a load of 2000 N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4 mm. E=200,000 MPa
A circular rod subjected to a tensile load of 13 KN having a gauge length of 30mm, extends to a length of 3mm. Given the tensile strength as 640 N\mm2, determine, a) Diameter of the rod (express in mm) b) Strain c) Modulus of elasticity (express in KPa) d) % elongation
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.001L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of L, determine the elongation of the block.
Three steel rods (E5 29 3 106 psi) support an 8.5-kip load P. Each of the rods AB and CD has a 0.32-in2 cross-sectional area and rod EF has a 1-in2 cross-sectional area. Neglecting the deformation of bar BED, determine (a) the change in length of rod EF, (b) the stress in each rod.