Answered: Consider a pipe carrying water at a…

Consider a pipe carrying water at a temperature of 60°F. The pipe diameter is 4 inches and the water velocity 5.7 ft/s. Will the flow be laminar or turbulent?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.37P

See similar textbooks

Related questions

Q: problem 1 1) A stream of 21,000 kg/h of steam flows steadily through of a turbine, entering at 3.5…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Figure shows a diagram from an impact strength test of metals that have three different crystal…

A: Solution: Given Data: To Find: a) What type of crystal structures do the curves (I), (II) and…

Q: Determine the factor of safety for infinite life fatigue (N> 1 million cycles) for a steel -45 MPa,…

A: To find: The factor of safety. Given: The maximum stress is σmax=115 MPa. The minimum stress is…

Q: Identify the zero-force members in the truss.

Q: In structures deformation or strain may be the result of ___________. Choose all that apply…

A: Introduction: Deformation is the amount an object is stretched, while strain is the ratio of…

Q: A stiff, square, thick rubber plate (m = 502 g) sits on the round mouth of a jar, completely…

Q: 8. For the plane truss loaded as shown below, use the method of joints to calculate the force in…

Q: The power P required for operating a pump depends on the diameter of the pump D, the pressure rise…

Q: A metal plate has the shape of an equilateral triangle with a side length of 2 meters. It is…

Q: If the stairs in the figure are not moving, determine the constant speed at which a man with a mass…

A: In this simply we have used the geometry to find the angle and then power formula to calculate the…

Q: 0₁ 0₂

A: Introduction:- Due to the relative motion of objects in several frames of reference, the distance…

Q: 2. End B of the slender rod AB slides down the inclined plane with the velocity shown, while end A…

Q: After pressure spraying, there is a thin layer of water (at 70°F) left inside of a 24 inch diameter…

Q: Explain Robotics systems & Humanoids & Telemedicine/Remote Surgery

A: Introduction: Robotic system: Robotic system is the connection between the human being and…

Q: AN AUTOMOBILE TIRE CONTAINS 3730 cu. in. OF AIR AT 32 psig AND 800f. (a) What mass of air is in the…

Q: In a solid fuel cell cathode reaction what 'waste' product is produced? O Hydrogen O Oxygen O Water…

Q: The moment of inertia I is always computed relative to a reference point or axis. True False

A: The answer is TRUE MOMENT OF INERTIA: Moment of Inertia indicates the distribution of particles…

Q: (a) As shown in Figure 2.1, an architect with an artistic flair designs a gate ABC to trap liquid of…

Q: Determine the components of the reactions at A and E, (a) if a 760-N load is applied as shown at C,…

Q: A steel plate used for polymer forming is to be bent into a circular shape having an inside radius…

Q: The overworked Amazon delivery person is driving up a steep hill with an incline of 26° when a box…

A: To find: The work done: Given: The inclination angle is θ=26°. The mass of the box is m=3.5 kg. The…

Q: 4. A steel rod of 3 cm diameter is enclosed centrally in a hollow copper tube of external diameter 5…

Q: ) The 100-mm long 2014-16 aluminum rodi has a diameter of 15 mm. If an axial tensile load of 10 KN…

Q: Q-Find the solution by using the simplex method? 1- Max Z=3X1+2X2 S. T: X1+X2 ≤ 4 X1-X2 <2 X1, X2 ≥0

Q: INPUT Sensing Display (MACHINE) Information Storage Processing HUMAN (MONITOR) FEEDBACK Action…

A: The following steps are included in the above block diagram - 1. Input 2. Machine controller…

Q: Using the biomechanical power curve shown, determine the maximum speed (in m/s) attained by the…

A: Given data : Total mass of the rider and the bicycle = 78 kg Slope of the hill = 20° From the given…

Q: 1.Equivalent resisitance through entire system 2.Current being drawn from battery 3.Current…

A: To find: The following: Given: The circuit is shown below.

Q: el rate c) indicated thermal efficiency d

A: Given-Information:- Generator Efficiency, ηG = 94%Mechanical Efficiency, ηM = 83%Indicated Power, Ip…

Q: Q2. A compound shaft supports five pulleys that transmit different amount of torques as shown in…

Q: 2. For this series of 4 questions, a 1-lb ball is dropped from rest and falls a distance before…

Q: A piece of cork having a specific weight of 2.36 kN/m is shaped as shown in Fig. 5.32. (a) To what…

Q: A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is…

Q: If the magnitude of the resultant force is to be 550 N, directed along the negative Y axis as shown…

Q: The figure below shows water flowing through a channel of uniform width (into the plane of the…

Q: Find the mass and center of mass of the solid E with the given density function p. m 11 (x, y, z) =…

A: In this the triple integration approach is being used to calculate the mass and centre of mass.

Q: 3. A copper-silver alloy is heated to 900°C (Figure Q1) and is found to consist of a and liquid…

Q: A lamp is tied with several rods as shown in the figure below. Determine the mass (kg) of the lamp…

A: Given:Force developed in the rod DE, TDE=150 NGravitational acceleration, g=9.81m/s2

Q: A team of engineers tasked with the design of a pipe system is currently sizing some of the…

A: Given:Diameter of pipe at section 1 for water flow, D1=0.1 mDiameter of pipe at section 2 for water…

Q: Problem-2: A double acting reciprocating pump running at 40 rpm is discharging 1 m³/min. The pump…

A: Percentage of slip is the ratio of difference of theoritical and actual discharge and theoritical…

Q: The graph below shows the acceleration of a simple harmonic motion versus time. Animation 1…

Q: The slope of the 5.0 kN force F is specified as shown in the figure. Express F as a vector in terms…

Q: 8. For the plane truss loaded as shown below, use the method of joints to calculate the force in…

Q: PROBLEM 2 Determine the magnitude of the couple C of the pulley shown if the resultant acts through…

Q: For the beam shown below, assume that E/= 6 x 104 kN-m² is constant through the leng beam. If a= 2…

A: The FBD of the diagram is Balancing the force equilibrium in the vertical direction R…

Q: 9- Choose the correct answer: 1. In a closed or dense air refrigeration cycle, the operating…

Q: The solid homogeneous cylinder is released from rest on the ramp. Determine the magnitudes of the…

Q: C. A substance has a total mass of 12.52 lbm and is under gravity at 30.5 ft/s². p (kg/m³) y (kN/m³)…

A: m=12.52 lbmg=30.5 ft/s2but, 1 ft = 12×2.54 cm =30.48 cm=0.3048 mg=9.2964 m/s2 Case 1: ρ=920…

Q: 2. Find the reactions RA and RB. A 0 2 m B 1m 52 N 67.4°

Q: The figure below shows a rectangular tank of dimensions ho = 2.5 m and b = 2 m is filled to the brim…

Q: Given the following state of stress at a point in a continuum, 523 3 0 0-21 -21 0 [a] = 3x² 0 MPa,…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Consider a pipe carrying water at a temperature of 60°F. The pipe diameter is 4 inches and the water velocity 5.7 ft/s. Will the flow be laminar or turbulent?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Someone claims that in fully developed turbulent flow in a pipe, the shear stress is a maximum at the pipe wall. Do you agree with this claim? Explain.
Water (ν = 0.86x10-6m2/s) flows through a tube with the diameter 12 mm at a velocity of 2 m/s. Determine if the flow is laminar or turbulent!
Consider a person walking first in air and then in water at the same speed. For which motion will the Reynolds number be higher?
A 6-cm-diameter horizontal water pipe expands gradually to a 9-cm-diameter pipe. The walls of the expansion section are angled 10° from the axis. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the head loss in the expansion section and the pressure in the larger-diameter pipe.
Glycerin at 40°C with ?? = 1252 kg/m3 and ?? = 0.27 kg/m·s is flowing through a 6-cm-diameter horizontal smooth pipe with an average velocity of 3.5 m/s. Determine the pressure drop per 10 m of the pipe. What is minor loss in pipe flow? How is the minor loss coefficient KL defined?
How does the wall shear stress ?w vary along the flow direction in the fully developed region in (a) laminar flow and (b) turbulent flow?
In fully developed laminar flow in a circular pipe, the velocity at R/2 (midway between the wall surface and the centerline) is measured to be 13 m/s. Determine the velocity at the center of the pipe.
Water at 75 degrees Celsius is flowing horizontally at a rate of 1.6 m^3/min in a pipe. It enters a 3-in 45 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 2in. If the pressure just before the elbow is 78 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
Gasoline (? = 680 kg/m3 and ? = 4.29 × 10−7 m2/s) is transported at a rate of 240 L/s for a distance of 2 km. The surface roughness of the piping is 0.03 mm. If the head loss due to pipe friction is not to exceed 10 m, determine the minimum diameter of the pipe.
Air is flowing at an average speed of 100 m/s through a 10-cm-diameter pipe. If the pipe undergoes an enlargement to 20 cm in diameter, determine the average speed in the enlarged pipe.
Consider the flow of oil with ? = 894 kg/m3 and ? = 2.33 kg/m·s in a 28-cmdiameter pipeline at an average velocity of 0.5 m/s. A 330-m-long section of the pipeline passes through the icy waters of a lake. Disregarding the entrance effects, determine the pumping power required to overcome the pressure losses and to maintain the flow of oil in the pipe.
In a laminar flow through a circular tube of radius of R, the velocity and temperature profiles at a cross section are given by u = u0 (1- r2/R2) and T(r) = A 1+Br2 - Cr4 where A, B and C are positive constants. Obtain a relation for the bulk fluid temperature at that cross section.