Answered: A shaft when subjected to pure torsion…

A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is 6.1359 x 10-3 m4, determine the maximum torque the shaft could handle.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Related questions

Q: Draw the isometric drawing given the following multiview projections

A: Find Draw an isometric view of the given object.

Q: In a company there are the following consumptions for energy and energetics. The company works 8…

A: Given: Electrical energy - 10 kWh/day Work = 111.76 kcal/h Mass flow rate = 0.25 lbm/h Density =…

Q: Determine the maximum absolute shear stress for the state of stress at a point shown. a. b. 0 50.0…

Q: The diffusion coefficient for carbon in BCC iron at 400C and 900C is given as 3.80x10-13 and…

A: First with the given data we will find the unknowns of the diffusion equation and then calculate the…

Q: à long insulated tube is doped with an exothermic ma- erial which generates steady and uniform heat…

Q: der (d) You are to compare the magnitude of the maximum heat flux anywhere in two objects. The…

Q: (d) You are to compare the magnitude of the maximum heat flux anywhere in two objects. The objects…

Q: A 650 bhp Diesel Engine with 6 cylinders has a brake thermal efficiency of 36 % and a jacket water…

A: Given : P = 650 HP = 650*0.7457 KW n = 6 ηₜ = 36% Lw = 27 % = 0.27Q dTw = 12⁰C dTc = 5 ⁰C

Q: Find the height h to which the following tank can be filled with water (density=1000 kg/m³) without…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given:Initial pressure of the refrigerant, P1=100 kPaVolume flow rate, Q=0.6 m3/minFinal pressure of…

Q: Given : A 1-[²₁5] and 2 -7 6 Find the following 4. A-2² 5. A B 7 -[23] = 0

Q: A basketball has a 300-mm outer diameter and a 3-mm wall thickness. Determine the normal stress in…

A: Outer diameter, D = 300 mm Wall thickness, t = 3 mm Inner diameter, d = D - 2t = 300 - (2*3) d =…

Q: Find out the local convection coefficient for a flow over a flat plate at a distance of 0.2 m from…

A: Given, Temperature of water, Tw= 60∘CVelocity of water, v= 2m/sFilm temperature, Tf= 40∘CWe should…

Q: Consider an underdamped mass spring system with mass m 1 kg spring constant k = 8 N/m, and damping…

A: Given: m=1 kg k=8 N/m a=4 N-s/m To find:

Q: Find the maximum weight of the lamp if the cords cannot support more than 20 lbf. Also find 0. 60⁰ A

Q: Moment of inertia is a measure of cross-sectional stiffness, whereas the modulus of elasticity E is…

A: Introduction: Moment of inertia: The rotational analogue of mass for linear motion is known as…

Q: According to the rigid body system shown in figure below, describe type of motion of the collar C,…

Q: When the true strain equals 0.14 and the true stress equals 355 MPa, the tensile test specimen…

Q: thermodynamics question: A rigid tank contains 2 kg of saturated water at 100 kPa. It is heated…

A: Given that: Mass of water inside the rigid tank = 2 kg Initially water is at saturated liquid…

Q: 2. Determine the resultant reaction at A and the tension reaction at B. (Final answers in N, 3…

Q: The outlet area of the nozzles in a simple impulse turbine is 15.5 cm2? and the steam leaves them…

Q: A single degree damped vibrating system is formed of a block of mass m= 10 kg, a spring of K= 100…

Q: A piston-cylinder device contains satuated water vapor with a constant pressure. The mass and the…

Q: or a Diesel cycle, which of the following statements is true? a. The compression process is a…

Q: A plot of the Stress Amplitude (S) (MPa) data versus Log10 Cycles To Failure (N) data of a typical…

A: Solution: Given Data: σy=300 MPaσUTS=650 MPaN=20000 cycles To Find: The fatigue strength in MPa

Q: An undamped spring mass system has a mass of 10 kg and a spring stiffness of 2250 N/m. It is excited…

Q: Determine the centrodes of a slider-crank mechanism, whose crank length, OAA, is equal to the…

Q: What is the pressure difference across the valve prior to being opened? The pressure at the inlet…

A: Given Dataz1=12mz2=10mρ=1000 kg/m3P=200kPa

Q: Part B Blocks A and B have a masses of 170 kg and 290 kg, respectively. (Figure 2) The coefficient…

Q: For the given isometric drawing, draw the corresponding top, front, and right side view. L HRP FRP L…

A: Given question is related to basics of mechanical engineering design and design process.

Q: A single degree damped vibrating system is formed of a block of mass m 5 kg. a spring of K= 100 N/m…

A: Given: Mass of the block→m=5 Kg Spring constant→k=100 N/m The initial point is→Xo=100 mm=0.10 m The…

Q: A person extends her arm in a manner shown into the windy air outside the shrine. The is 53F and…

Q: Determine the Resultant Moment at point A of the system of forces shown below. Each square is 1ft…

A: Given: Find: The resultant moment at point A.

Q: A circular shaft AB of length L is fixed against rotation at the ends and loaded by a distributed…

A: According to the given free body diagram , Consider the torque equilibrium in vertical direction…

Q: 40-kg cylinder is hung from the gear system shown. Gear s a mass of 8 kg and a radius of gyration…

A: Given,

Q: Determine the maximum in-plane shearing stress for the state of stress at a point shown below. a. 0…

Q: Blocks A and B have a masses of 170 kg and 290 kg, respectively. (Eigure 2) The coefficient of…

Q: which bolt holds large load and why :M16X3 or M16X1

A: M16x3 indicates : Metric bolt with nominal diameter 16mm with pitch 3mm similarly M16x1 indicates…

Q: If you have the same shape (let say a slab) will the direction of the flow will it affect the value…

A: Consider following figure of a slab: There are two cases: 1. Flow along length direction and 2.…

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

Q: Using the data provided on the figure below, determine: a. Water volumetric flow rate. b. Dynamic…

A: Given data, From the given figure Diameter of pipe at point 1, D1 = 6 in = 0.5 ft Cross-sectional…

Q: What is an example of a negative entropy change in a system? a. It is not possible due to the…

A: The change of entropy is equal to the heat transfer (dQ) divided by the temperature (T).ie. ∆S=dQT

Q: Q1) A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt =…

Q: A 1.5 kg block is dropped from a height of 2.5 m onto a spring with a sp 1293.6 N/m. When the block…

A: Given data as per question m=1.5 kg h=2.5 m k=1293.6 N/m

Q: Cool water flows into a heat exchanger at 300 g/s (Cp = 4.16 kJ/kg K), T = 288.15 K and flows out at…

Q: 8. In single duct air conditioning system, the 1.5 kg/s of outlet air at -4°C db, 80% RH mixes with…

A: The mass of outlet air m1=1.5 kg/s. The relative humidity is RH=80% The temperature is t1=-4°C. The…

Q: The figure below shows a cable supporting a beam. In addition there is a vertical force acting on…

A: Given: The tension in the cable, T The support reactions at A are Ax and Ay.

Q: 30° 2m

Q: Higher values of moment of inertia (I), will result in higher stresses and deflections for beams and…

Q: A closed thin walled cylindrical vessel has a diameter D of 780 mm, a wall thickness t of 3.5 mm and…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is 6.1359 x 10-3 m4, determine the maximum torque the shaft could handle.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A shaft when subjected to pure torsion developed a stress of 50 Mpa. If polar moment of inertia is 6.1359 x 10 -7 m4 , determine the maximum torque the shaft could handle. A. 1.23 KN.m B. 1.68 KN.m C. 1.84 KN.m D. 2.48 KN.m
What is the minimum diameter of a solid steel shaft that will not twist through more than 6° in a 15-m length when subjected to a torque of 8 kN·m? Use G = 83 GPa.How can you make stress of the element (rho=55mm) in question be equal to 45MPa? Prove your answer
2: If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further subjected to a torque of 10 kN-m. The maximum principal stress experienced on the shaft is closest to a) 41 MPA b) 82 MPA c) 164 MPA d ) 204 Mpa
A hollow steel shaft is stressed to 55 MPa by a torque of 135600Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter and G = 83 GPa.
Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.
The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner diameter of the shaft is two-thirds of its outer diameter D. If the inner diameter is 8 inches, find the angle of twist of the shaft. Use G = 12 x 10^6 psi for steel.
Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm. ii) Bending moment of “M” Nm. r = 5 mm D = 50 mm d = 25 mm Torque “T” Nm = 150 Bending moment ‘’M’’ Nm = 250