Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 44 MPa in the direction shown, determine the principal stresses at the point. 85 MPa 56 MPa O 70.9 MPa and -97.0 MPa 82.8 MPa and -136.0 MPa 89.5 MPa and -64.2 MPa 75.1 MPa and -124.1 MPa 64.9 MPa and -105.9 MPa

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 44 MPa in the direction shown, determine the principal stresses at the point. 85 MPa 56 MPa O 70.9 MPa and -97.0 MPa 82.8 MPa and -136.0 MPa 89.5 MPa and -64.2 MPa 75.1 MPa and -124.1 MPa 64.9 MPa and -105.9 MPa

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

Determine the outside diameter of a hollow steel rod that will carry atensile load of 55,000 kg at a stress of 1,500 kg/cm2 and the wallthickness is 10 mm.A. 8.17 cm C. 12.67 cmB. 8.34 cm D. 7.28 cm
A horizontal bar of negligible mass, hinged at A in FIGURE Z and assume rigid, is supported by a bronze rod 2 m long and a steel rod 1 m long. For the steel rod, the area is 600 mm², and E = 200 GPa. For the bronze rod, the area is 300 mm², and E = 83 GPa. Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b. 1.36 mm c. 2.56 mm d. 3.18 mm
The normal stress (kN/cm2) at the K point resulting from the tensile force of P=1000 kN acting from the point B (in the z direction) eccentrically on the I section with dimensions b=30 cm, h=50 cm and t=5 cm shown in the figure below. calculate.
The stresses shown in the figure act at a point in a stressed body. If σ = 5.8 ksi in the direction shown, determine the shear stress at this point on the inclined plane shown. 5.23 ksi 8.31 ksi 7.76 ksi 7.14 ksi 4.31 ksi
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 450 mm2. Determine the average axial stress in each bar. q = 5 t = 0
The internal shear force at a certain section of a steel beam is V = 8.1 kN. The beam cross-section shown in the figure has dimensions of b=137 mm, c=33 mm, d=66 mm, and t=7 mm. Determine: the shear stress at point H. [Answer: 7.43 MPa]
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 ksi, Sy = 24 ksi, and Sxy = 16 ksi. (a) Determine the principal stresses (0p1 > 0p2) and the maximum in-plane shear stress max acting at the point. (b) Find the smallest rotation angle Op (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
Determine the shear stress at points A and B on the beam if it is subjected to ashear force of V = 400 kN. Represent the state of stress on a volume element of these points.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 23.6 ksi, Sy = 2.8 ksi, and Sxy = 7 ksi. Assume β=19∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 6 ksi, Sy = 22 ksi, and Sxy = 13 ksi.(a) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(b) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)